Главная
/
Textron
/
GREENLINE 920XC Series
/
Тренировка

Textron GREENLINE 920XC Series, Тренировка

Поделиться

50 страниц до
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79

Страница: 65 / 79

background image

Add Event

•

If an event on the measurement trace is

not listed in the events list (due to
inaccuracies caused by poor SNR or
inadequate parameter configuration), use
the “add event” function to manually add
this event into the events list.

•

Click the events list window, and select

“Add event” under the “Editing” menu.

•

Choose the type of event from the pull-

down menu, enter the event features, and
then press Enter to add the event to the
events list.

Add Event

«
...
63
64
65
66
67
...
»

Содержание GREENLINE 920XC Series
















































































Отзывы:

Нет отзывов

Похожие инструкции для GREENLINE 920XC Series

Бренд: Aaronia Страницы: 47

Бренд: Keithley Страницы: 201

Бренд: Larson Davis Страницы: 536

Бренд: Topcon Страницы: 62

Бренд: Keithley Страницы: 18

Бренд: Danfoss Страницы: 4

Бренд: WATERGUARD Страницы: 2

Бренд: PCB Piezotronics Страницы: 16

fieldscout TDR 100

Бренд: Spectrum Techniques Страницы: 20

Бренд: Datakom Страницы: 2

Smart Air Quality Monitor

Бренд: Lennox Страницы: 28

Бренд: Roland Страницы: 96

Бренд: Anritsu Страницы: 29

Бренд: VWR Страницы: 44

Бренд: Dewetron Страницы: 48

Бренд: K&K Sound Страницы: 2

Бренд: AlazarTech Страницы: 64

Бренд: Easy-Laser Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды