Texmo Industries Taro Pumps NCH 2250 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 34

Texmo Industries Taro Pumps NCH 2250 Скачать руководство пользователя страница 20

Electrical wiring work

Earthing

Warning

All electrical work must be performed by an authorised electrician in compliance with
local electrical equipment standards and internal wiring codes. Improper wiring can
lead to current leakage, electrical shock, or fire.

Warning

Be sure to install the ground wire securely. Failure to observe this
precaution could damage the pump and cause current leakage, which may
lead to electrical shock

Caution

Do not connect the ground wire to a gas pipe, water pipe, lightning rod, or
telephone ground wire. Improper grounding could cause electrical shock

Electrical Installation

Check the power supply voltage and frequency and compare with the product requirements
specified on the nameplate

Observe relevant EB regulations while providing power supply to the motor

As far as possible, do not use multiple joints in the electrical cabling while connecting the starter
to the pump

Ground the pump using the two earth screws provided on the leg of the motor body

Ensure electrical joints, if any, are properly and adequately insulated

Connect the cable properly to the starter terminals to avoid loose connections

Factor in low-voltage operation while selecting cable size

OMSP001A

20

2020.01

«
...
18
19
20
21
22
...
»

Содержание Taro Pumps NCH 2250



































Отзывы:

Нет отзывов