Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com
Page 12
FX-B101Q-DCA_DCV manual (d0103)
Clear Lockable NEMA 4X
Splash Proof Lens Cover
P/N.(OP-N4/144X36 )
133.5mm
(5.27")
Mosaic
Fitting
9/64 DIN
cutout
spacer
To open rear cover,
use a small flat
blade screw driver.
Press down lightly
to release catch and
leaver outwards.
SIDE VIEW
137.7mm
(5.42")
9/64 DIN
cutout
spacer
142.3mm
(5.62")
Max. panel thickness
43mm
(1.7")
For additional strength,
extra Mounting Slide Clips
can be ordered and doubled up
one behind the other.
P/N. (75-DMC144X36)
4.5mm
(0.18")
Metal Surround Case
P/N.(OP-MTL144X36) is pre-installed
at the factory and cannot be removed
without damage to the case.
Two bezel Trim
Strips are supplied with
each Panel Adaptor
Panel Adaptor to fit existing 6" Edgewise
Pointer Meter Cut-Outs P/N.(OP-PA/144x36)
Adaptor uses wide jaw mounting slide
clips.P/N.(75DMC14436B)
When extra panel
mounting tightness is
required,
order the optional
screw mount
clip.
P/N
.(O
PM
TL
CL
IP)
FRONT VIEW
144mm
(5.69")
36mm
(1.42")
4mm
(0.16")
typical
9/64 DIN
36x144 mm
100
0
10
30
50
70
90
20
40
60
80
4
3
2
1
P
SP
PANEL CUTOUT
138mm
(5.45")
33mm
(1.3")
Snug
Fitting
Loose
Fitting
8 places
7.5mm(0.3")
3.5mm(0.14")
4 places
4 places
32.2 mm
(1.27")
Mosaic
Fitting
133mm
(5.25")
135.2mm
(5.34")
3mm(0.12")
9/64 DIN
cutout
spacer
Case will mount in standard DIN cutouts
Various
bezel colors
are available.
Black is
standard.
The Metal Surround
case uses Metal
Screw Mount Clips
and has a max.
panel thickness
mounting of
7mm(0.28")
TOP VIEW
5mm
(0.20")
117.5mm
(4.64")
18.3mm (0.72")
Straight-thru
Connector
31mm
(1.22")
34mm
(1.34")
Mosaic Fitting
Right-angled
Connector
6mm
(0.24")
10mm
(0.39")
26.5mm (1.05")
Push-On Connector
for FI series IO board
The adapter snaps on
the 36x144 mm
(1.42"x5.69") case and
enables single unit or
stack mounting in an
existing 6" edgewise
pointer meter cut-out.
100
0
25
50
75
100
0
25
50
75
SP1 SP2
SP3 SP4
Zero Span
Zero Span
Panel adaptor plates are
available to retrofit most
existing panel cutouts.
31mm
(1.22")
These dimensions are
increased by 2mm (0.08") when
the
metal surround case is installed.
For extra strength in portable applications,
the 8 DIN spacers should be snipped
off and the
Mosaic fitting cutout used.
Controls and Indicators
Case Dimensions
This rugged, impact resistant, clear lens cover is
designed to be dust and water proof to NEMA 4 and
IP65 standards. The lens cover consists of a base
and cover with a cam hinge and key-lock locking
device.
An O-ring, or neoprene gasket forms a seal between
the base and the panel. When opened, a cam hinge
prevents the cover from closing until pushed closed.
The cover has a tapered recess that, when closed,
forms a capillary seal with a tapered ridge on the
base. A capillary seal is created when capillary
action causes a small amount of water to be drawn
in between the two surfaces producing a water tight
film around the sealing area.
For those applications, such as food processing,
where fluid residues are unacceptable, apply a light
coating of clear silicone grease, or other approved
sealant to the mating grove to prevent any ingress
of liquid and enable the cover to withstand steam
cleaning.
Turning the key-lock tightens the cover to the base,
ensuring seal integrity. A safety catch keeps the
cover closed even when the key is turned to the
open position and removed. The keyhole can also
be used to attach a safety seal clip, preventing
unauthorized opening.
Hinged Clear Lockable Polycarbonate NEMA 4X Splash Proof Cover
9/64 DIN
36x144 mm (1.42"x5.69")
P/N: OP-N4/144X36
Base
O-ring
Gasket
Cover
Removable
Key-lock
Panel
Safety
Catch
