An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
SLOS732G – JUNE 2011 – REVISED MARCH 2020
TRF7960A Multiprotocol Fully Integrated 13.56-MHz RFID Reader/Writer IC
1
Device Overview
1
1.1
Features
1
• Completely Integrated Protocol Handling for
ISO/IEC 15693, ISO/IEC 18000-3,
ISO/IEC 14443A, ISO/IEC 14443B, NFC Forum
Device Types 2 to 5, and FeliCa™
• Input Voltage Range: 2.7 VDC to 5.5 VDC
• Programmable Output Power:
+20 dBm (100 mW) or +23 dBm (200 mW)
• Programmable I/O Voltage Levels:
1.8 VDC to 5.5 VDC
• Programmable System Clock Frequency Output
(RF, RF/2, RF/4)
• Programmable Modulation Depth
• Dual Receiver Architecture With RSSI for
Elimination of "Read Holes" and Adjacent Reader
System or Ambient In-Band Noise Detection
• Programmable Power Modes for Ultra-Low-Power
System Design (Power Down <0.5 µA)
• Parallel or SPI Interface
• Integrated Voltage Regulator for Microcontroller
Supply
• Temperature Range: –40°C to 110°C
• 32-Pin QFN Package (5 mm × 5 mm) (RHB)
1.2
Applications
•
Secure Access Control
•
Product Authentication
•
Digital Door Locks
•
Public Transport or Event Ticketing
•
Medical Systems
•
Remote Sensor Applications
1.3
Description
The TRF7960A device is an integrated analog front-end (AFE) and multiprotocol data-framing device for a
13.56-MHz
reader/writer system that supports ISO/IEC 14443 A and B, Sony FeliCa, and
ISO/IEC 15693. Built-in programming options make it suitable for a wide range of applications for
proximity and vicinity identification systems.
The reader is configured by selecting the desired protocol in the control registers. Direct access to all
control registers allows fine tuning of various reader parameters as needed.
The TRF7960A device supports data rates up to 848 kbps with all framing and synchronization tasks for
the ISO protocols onboard. The device also supports reader/writer mode for NFC Forum tag types 1, 2, 3,
4, and 5. NFC Forum tag types 2, 3, 4, and 5 are supported with the built-in protocol decoders used in
Direct Mode 2. NFC Forum tag type 1 requires the use of Direct Mode 0. Other standards and custom
protocols can also be implemented by using Direct Mode 0. Direct Mode 0 lets the user fully control the
AFE and also gain access to the raw subcarrier data or the unframed, but already ISO-formatted, data and
the associated (extracted) clock signal.
The receiver system has a dual-input receiver architecture to maximize communication robustness. The
receivers also include various automatic and manual gain control options. The received signal strength
from transponders, ambient sources, or internal levels is available in the RSSI register.
A SPI or parallel interface can be used for the communication between the MCU and the TRF7960A
reader. When the built-in hardware encoders and decoders are used, transmit and receive functions use a
12-byte FIFO register. For direct transmit or receive functions, the encoders or decoders can be bypassed
so the MCU can process the data in real time.
The TRF7960A device supports a wide supply voltage range of 2.7 V to 5.5 V and data communication
levels from 1.8 V to 5.5 V for the MCU I/O interface.
The transmitter has selectable output power levels of 100 mW (+20 dBm) or 200 mW (+23 dBm)
equivalent into a 50-
Ω
load when using a 5-V supply and supports OOK and ASK modulation with
selectable modulation depth.
