background image

Host

Computer

USB Cable

USB

Interface

Adapter

Green LED

Indicates

Power

10-Pin

Ribbon

Cable

EVM Board

USB Interface Adaptor Quick Connection Diagram

www.ti.com

Setup

2.3

Hardware Setup

Table 2

shows the board default jumper settings.

Table 2. Default Jumper Settings

JUMPER

DEFAULT

JP1

Installed across pins 1 and 2

JP2

Installed across pins 2 and 3

JP3

Installed across pins 2 and 3

JP4

Installed across pins 1 and 2

Connect the USB-TO-GPIO adapter to your PC using the supplied USB cable. Connect the
TPS6236xEVM connector J8 to the USB-TO-GPIO adapter using the supplied 10-pin ribbon cable. The
connectors on the ribbon cable are keyed to prevent incorrect installation.

Connect the load (processor) to either the output headers J4 and J6 (for currents below 1A) or to the
output terminal block J7 (for currents greater than 1A). The leads should be short and twisted.

Connect the SNS+ and SNS- signals from header J5 to the load. For proper regulation, these must be
connected to the output.

Install jumpers, JP1 through JP4 to the desired positions. Jumper JP1 must be across pins 1 and 2 for the
TPS6236x to operate.

Connect at least a 3 A rated input power supply, set to provide between 2.5V and 5.5V, between J1 and
J3. The leads should be short and twisted. Turn on the power supply.

5

SLVU425A

April 2011

Revised July 2011

TPS6236xEVM-655

Submit Documentation Feedback

Copyright

©

2011, Texas Instruments Incorporated

Содержание TPS6236 EVM-655 Series






















Отзывы: