manualshive.com logo in svg

Texas Instruments TPS6100 EVM Series, Руководство пользователя

Поделиться
Скачать
Texas Instruments TPS6100 EVM Series Скачать руководство пользователя страница 16

4-2

4.1

Setup of the EVM

Figure 4–1. Setup of the EVM

Current Meter

for Input Current

(See Note A)

+

–

Power

Supply

Oscilloscope

for Output Voltage
and Output Ripple

Voltage Meter for

LBO Output Voltage

Voltage Meter

for Input Voltage

Current Meter

for Output Current

Important

LOAD

Note A: Use this current meter only if the sense wires of the supply are used.

Follow these steps for proper operation of the EVM:

1) Connect J1, the Enable-pin, with V

DD

 as shown in Figure 4–1.

2) Connect the sense wires of the power supply to the input terminals of the

board, or solder the connections of the power supply to the terminals.

3) Connect the input voltage meter between the board on the one side and

the power supply and input current meter on the other side.

4) Connect the oscilloscope between the output terminals of the EVM on the

one side and the load and output current meter on the other side.

Содержание TPS6100 EVM Series



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды