Texas Instruments TPA0162 Скачать руководство пользователя страница 8

Страница: 8 / 36

Feature Highlights

1-2

Introduction

1.1

Feature Highlights

The TI TPA0162 audio amplifier evaluation module and the TI plug-n-play
audio amplifier evaluation platform include the following features:

TPA0162 Stereo 2-W Audio Power Amplifier Evaluation Module

Internal depop circuitry to minimize transients in outputs

Powers up at mute volume level to avoid pop

Dual channel, bridge-tied load (BTL) or single-ended operation

2 W per channel output power into 3

Ω

at 5 V, BTL

Low current consumption in shutdown mode (150

Internal input MUX selects among two sets of stereo inputs

Digital volume control from +20 dB to –40 dB

Microprocessor mode volume control

Differential stereo inputs

PC Beep input

Quick and Easy Configuration With The TI Plug-N-Play Audio Amplifier
Evaluation Platform

Evaluation module is designed to simply plug into the platform,
automatically making all signal, control, and power connections

Platform provides flexible power options

Jumpers on the platform select power and module control options

Switches on the platform route signals

Platform provides quick and easy audio input and output connections

Platform Power Options

External 5-V – 15-V DC V

supply inputs

External regulated V

supply input

Socket for on-board 5 V/3.3 V V

voltage regulator EVM

On-board overvoltage and reverse polarity power protection

Platform Audio Input and Output Connections

Left and right RCA phono jack inputs

Miniature stereo phone jack input

Left and right RCA phono jack outputs

Left and right compression speaker terminal outputs

Miniature stereo headphone jack output

Содержание TPA0162





































Результаты поиска

Содержание TPA0162

Отзывы:

Texas Instruments TPA0162, Руководство пользователя, Страница: 8 / 36

Результаты поиска

Содержание TPA0162

Отзывы: