manualshive.com logo in svg

Texas Instruments TMS570LC4357, Техническое справочное руководство


Поделиться
Скачать
background image

Basic Operation

www.ti.com

1534

SPNU563A – March 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

Multi-Buffered Serial Peripheral Interface Module (MibSPI) with Parallel Pin
Option (MibSPIP)

28.2.11.2 MibSPI Mode Configuration

The following list details the configuration steps that software should perform prior to the transmission or
reception of data in MIBSPI mode. As long as the SPIEN bit in the Global Control Register 1 (SPIGCR1)
is cleared to 0 the entire time that the SPI is being configured, the order in which the registers are
programmed is not important.

•

Enable SPI by setting RESET bit.

•

Set MSPIENA bit to 1 to get access to multi-buffer mode registers.

•

Configure the SIMO, SOMI, CLK, and optional SPICS and SPIENA pins for SPI functionality by setting
the corresponding bit in SPIPC0 register.

•

Configure the module to function as Master or Slave using CLKMOD and MASTER bits.

•

Configure the required SPI data format using SPIFMTx register.

•

If the module is selected to function as Master, the delay parameters can be configured using
SPIDELAY register.

•

Check for BUFINITACTIVE bit to be active before configuring MIBSPI RAM. (From Device Power On it
take Number of Buffers × Peripheral clock period to initialize complete RAM.)

•

Enable the Transfer Group interrupts using TGITENST register if required.

•

Enable error interrupts using SPIINT0 register if required.

•

Set SPIEN bit to 1 after the SPI is configured.

•

The Trigger Source, Trigger Event, Transfer Group start address for the corresponding Transfer
groups can be configured using the corresponding TGxCTRL register.

•

Configure LPEND to specify the end address of the last TG.

•

Similar to SPIDAT1 register, the 16 bit control fields in every TXRAM buffer in the TG have to be
configured.

•

Configure one of the eight BUFMODE available for each buffer.

•

Fill the data to be transmitted in TXDATA field in TXRAM buffers.

•

Configure TGENA bit to enable the required Transfer groups. (In case of Trigger event always setting
TGENA will trigger the transfer group).

•

At the occurrence of the correct trigger event, the Transfer group will be triggered and data gets
transmitted and received one after the other with out any CPU intervention.

•

You can poll Transfer group interrupt flag or wait for a transfer-completed interrupt to read and write
new data to the buffers.

Содержание TMS570LC4357

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS570LC4357

MADRIX AURA Technical Manual & Quick Start Manual preview
AURA
Бренд: MADRIX Страницы: 36
2M Technology 2MTHFR-2M Quick Manual preview
2MTHFR-2M
Бренд: 2M Technology Страницы: 17
2iB SC10 Quick Start Manual preview
SC10
Бренд: 2iB Страницы: 5
Galaxy Control Systems 635 Series Worksheet preview
635 Series
Бренд: Galaxy Control Systems Страницы: 5
Parker AC890PX Series User Mounting And Assembly Instructions preview
AC890PX Series
Бренд: Parker Страницы: 30
Parker Compax3M Series Installation Manual preview
Compax3M Series
Бренд: Parker Страницы: 52
Parker AC30V Series Manual preview
AC30V Series
Бренд: Parker Страницы: 337
Wavelength Electronics PTC5000 Datasheet And Operating Manual preview
PTC5000
Бренд: Wavelength Electronics Страницы: 17
D+H DXD 150-K-BSY+ Original Instructions Manual preview
DXD 150-K-BSY+
Бренд: D+H Страницы: 20
DPS Telecom NetGuardian LPG D-PK-NGLPG User Manual preview
NetGuardian LPG D-PK-NGLPG
Бренд: DPS Telecom Страницы: 82
JBL LED SOLAR CONTROL WIFI Quick Manual preview
LED SOLAR CONTROL WIFI
Бренд: JBL Страницы: 16
Fisher 67D Series Instruction Manual preview
67D Series
Бренд: Fisher Страницы: 12
Numatics SentronicD Installation Manual preview
SentronicD
Бренд: Numatics Страницы: 13
Magnetek GPD 333 Technical Manual preview
GPD 333
Бренд: Magnetek Страницы: 81
M-system 18PP Instruction Manual preview
18PP
Бренд: M-system Страницы: 3
EPOS EPOS2 50/5 Application Note preview
EPOS2 50/5
Бренд: EPOS Страницы: 21
DGFLOW PRESFLO User Manual preview
PRESFLO
Бренд: DGFLOW Страницы: 4
microHAM STATION MASTER Manual preview
STATION MASTER
Бренд: microHAM Страницы: 70

Бренды по названию

Популярные бренды

Загрузить еще бренды