manualshive.com logo in svg

Texas Instruments TMS320x281 series, Справочное руководство

Поделиться
Скачать
Texas Instruments TMS320x281 series Скачать руководство пользователя страница 68

3.1

CAN Module Initialization

Normal mode

(CCR = 0)
(CCE = 0)

Configuration mode requested

(CCR = 1)
(CCE = 0)

Wait for configuration mode

(CCR = 1)
(CCE = 0)

CCE = 0

Configuration mode active

(CCR = 1)
(CCE = 1)

Changing of bit timing

parameters enabled

Normal mode requested

(CCR = 0)

CCE = 1

Wait for normal mode

(CCR = 0)
(CCE = 1)

CCE = 1

Initialization complete

Normal mode

CAN Module Initialization

www.ti.com

The CAN module must be initialized before the utilization. Initialization is only possible if the module is in
initialization mode.

Figure 3-1

is a flow chart showing the process.

Programming CCR (CANMC.12) = 1 sets the initialization mode. The initialization can be performed only
when CCE (CANES.4) = 1. Afterwards, the configuration registers can be written.

SCC mode only:

In order to modify the global acceptance mask register (CANGAM) and the two local acceptance mask
registers [LAM(0) and LAM(3)], the CAN module also must be set in the initialization mode.

The module is activated again by programming CCR(CANMC.12) = 0.

After hardware reset, the initialization mode is active.

Note:

If the CANBTC register is programmed with a zero value, or left with the initial value, the
CAN module never leaves the initialization mode, i.e. CCE (CANES.4) bit remains at 1 when
clearing the CCR bit.

Figure 3-1. Initialization Sequence

Note:

The transition between initialization mode and normal mode and vice-versa is performed in
synchronization with the CAN network. That is, the CAN controller waits until it detects a bus
idle sequence (= 11 recessive bits) before it changes the mode. In the event of a
stuck-to-dominant bus error, the CAN controller cannot detect a bus-idle condition and
therefore is unable to perform a mode transition.

eCAN Configuration

68

SPRU074F – May 2002 – Revised January 2009

Submit Documentation Feedback

Содержание TMS320x281 series





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды