Texas Instruments TMS320VC5509A Скачать руководство пользователя страница 9

Страница: 9 / 33

SPRZ200E

TMS320VC5509A Silicon Errata

Known Design Marginality/Exceptions to Functional Specifications

3.1

Summary of Advisories

Table 2 provides a quick reference of all advisories by number, silicon revision affected, and lists their respective
page location.

Table 2. Quick Reference Table

Advisory

Number

Advisory

Revision(s)

Affected

Page

Device-Level Advisories

DL_2

Software Modification of MPNMC Bit is Not Pipeline-Protected

1.0 and 1.1

DL_7

RETI Instruction may Affect the XF State

1.0 and 1.1

DL_10

First Word of Data on Consecutive DMA Transmissions Using McBSP is Lost

1.0 and 1.1

Bootloader Advisories

BL_3

USB Bootloader Returns Incorrect DescriptorType Value When String Descriptors are Requested
by the Host

1.0 and 1.1

BL_4

USB Bootloader Returns Incorrect PID During Enumeration Phase

1.0 and 1.1

Direct Memory Access (DMA) Advisories

DMA_1

Early Sync Event Stops Block Transfer

1.0 and 1.1

DMA_2

DMA Does Not Support Burst Transfers From EMIF to EMIF

1.0 and 1.1

External Memory Interface (EMIF) Advisories

EMIF_8

ARDY Pin Requires Strong Pullup Resistor

1.0 and 1.1

EMIF_9

External Memory Write After Read Reversal

1.0 and 1.1

EMIF_10

Block Write Immediately Following a Block Read May Cause Data Corruption

1.0 and 1.1

EMIF_11

EMIF Asynchronous Access Hold = 0 is Not Valid for Strobe > 3

1.0 and 1.1

EMIF_12

8-Bit Asynchronous Writes on 5509A EMIF Not Supported

1.0 and 1.1

EMIF_13

After Changing CE Control Registers and Disabling SDRAM Clock in Divide-by-8 and Divide-by-16
Modes, Asynchronous Access Followed by SDRAM Access Will Not Supply a Ready Signal to CPU

1.0 and 1.1

EMIF_14

SETUP = 2 Configuration is not Valid for Asynchronous Memory

1.0 and 1.1

Enhanced Host Port Interface (EHPI) Advisories

EHPI_5

HPID Read Following a HPID Write While HRDY Low Corrupts the Read

1.0 and 1.1

EHPI_6

HPIC/HPIA Access Following an Autoincremented HPID Write Causes Next HPID Address to Increment
to the Incorrect Address

1.0 and 1.1

EHPI_7

HRDY is Always Driven

1.0 and 1.1

Real-Time Clock (RTC) Advisories

RTC_3

RTC Interrupts are Perceived by the User as Happening One Second Before

1.0 and 1.1

RTC_4

Any Year Ending in 00 Will Appear as a Leap Year

1.0 and 1.1

RTC_5

Midnight and Noon Transitions Do Not Function Correctly in 12h Mode

1.0 and 1.1

Universal Serial Bus (USB) Advisories

USB_2

CPU Might Miss Back-to-Back USB Interrupts When CPU Speed is Less Than or Equal to 24 MHz

1.0 and 1.1

USB_5

USB Input Cell Does Not Power Down When USB is Placed in IDLE

1.0 and 1.1

USB_6

CPU Read/Write to USB Module may Return Incorrect Result if the USB Clock is Running Slower Than
Recommended Speed (48 MHz)

1.0 and 1.1

Содержание TMS320VC5509A

































Результаты поиска

Содержание TMS320VC5509A

Отзывы:

Похожие инструкции для TMS320VC5509A

Бренды по названию

Популярные бренды

Texas Instruments TMS320VC5509A, Руководство пользователя

Результаты поиска

Содержание TMS320VC5509A

Отзывы:

Похожие инструкции для TMS320VC5509A

Бренды по названию

Популярные бренды