manualshive.com logo in svg

Texas Instruments TMS320VC5509, Справочное руководство


Поделиться
Скачать
background image

Data Receive Registers (DRR1 and DRR2)

McBSP Registers

12-2

SPRU592E

12.1 Data Receive Registers (DRR1 and DRR2)

The CPU or the DMA controller reads received data from one or both of the
data receive registers (see Figure 12

−

1). If the serial word length is 16 bits or

smaller only DRR1 is used. If the serial length is larger than 16 bits, both DRR1
and DRR2 are used, and DRR2 holds the most significant bits. Each frame of
receive data in the McBSP can have one phase or two phases, each with its
own serial word length.

DRR1 and DRR2 are I/O mapped registers; they are accessible at addresses
in I/O space.

Figure 12

−

1. Data Receive Registers (DRR1 and DRR2)

DRR2

15

0

High part of receive data (for 20-, 24- or 32-bit data)

R/W-0

DRR1

15

0

Receive data (for 8-, 12-, or 16-bit data) or Low part of receive data (for 20-, 24- or 32-bit data)

R/W-0

Legend:

R = Read; W = Write; -

n

 = Value after reset

12.1.1 How Data Travels From the Data Receive (DR) Pin to the DRRs

If the serial word length is 16 bits or smaller, receive data on the DR pin is
shifted into receive shift register 1 (RSR1) and then copied into receive buffer
register 1 (RBR1). The content of RBR1 is then copied to DRR1, which can be
read by the CPU or by the DMA controller.

If the serial word length is larger than 16 bits, receive data on the DR pin is
shifted into both of the receive shift registers (RSR2, RSR1) and then copied
into both of the receive buffer registers (RBR2, RBR1). The content of the
RBRs is then copied into both of the DRRs, which can be read by the CPU or
by the DMA controller.

If companding is used during the copy from RBR1 to DRR1
(RCOMPAND = 10b or 11b), the 8-bit compressed data in RBR1 is expanded
to a left-justified 16-bit value in DRR1. If companding is disabled, the data
copied from RBR[1,2] to DRR[1,2] is justified and bit filled according to the
RJUST bits.

The RSRs and RBRs are not accessible. They are not mapped to I/O space
like the DRRs.

Содержание TMS320VC5509






























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320VC5509

Raidon SAFETank Series User Manual preview
SAFETank Series
Бренд: Raidon Страницы: 49
Opvimus UMX-ETH+ Operating Instructions Manual preview
UMX-ETH+
Бренд: Opvimus Страницы: 12
ForeScout CounterACT Quick Installation Manual preview
CounterACT
Бренд: ForeScout Страницы: 28
Maxim MAX1415 Specification Sheet preview
MAX1415
Бренд: Maxim Страницы: 14
Dahua DHI-NVR2104-P-4KS2 Quick Start Manual preview
DHI-NVR2104-P-4KS2
Бренд: Dahua Страницы: 23
ZALMAN ZM-WB2 Gold User Manual preview
ZM-WB2 Gold
Бренд: ZALMAN Страницы: 9
Advantech MIC-730AI User Manual preview
MIC-730AI
Бренд: Advantech Страницы: 36
Caen A 1735 Technical Information Manual preview
A 1735
Бренд: Caen Страницы: 14
Pressalit Care Indivo RK1010 User And Maintenance Manual preview
Indivo RK1010
Бренд: Pressalit Care Страницы: 31
Bailey INFI 90 NTAI06 Instruction preview
INFI 90 NTAI06
Бренд: Bailey Страницы: 33
SmartBridges airPoint Nexus sB3210 User Manual preview
airPoint Nexus sB3210
Бренд: SmartBridges Страницы: 55
ekwb 3831109819395 Manual preview
3831109819395
Бренд: ekwb Страницы: 10
Grundfos CIM 060 Installation And Operating Instructions Manual preview
CIM 060
Бренд: Grundfos Страницы: 40
Paradyne SMD2000-24E Installation Instructions Manual preview
SMD2000-24E
Бренд: Paradyne Страницы: 28
Patton electronics OnSite 9100 Quick Start Manual preview
OnSite 9100
Бренд: Patton electronics Страницы: 8
National Instruments GPIB-120A User Manual preview
GPIB-120A
Бренд: National Instruments Страницы: 36
Devolo Kurulum Manual preview
Kurulum
Бренд: Devolo Страницы: 24
Maco RUSTICO 13321 Installation Instructions Manual preview
RUSTICO 13321
Бренд: Maco Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды