manualshive.com logo in svg

Texas Instruments TMS320C6A816 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Preliminary

www.ti.com

Registers

9.4.9 Power Counter Register (SD_PWCNT)

This register is used to program a counter to delay command transfers after activating the PAD power,
this value depends on PAD characteristics and voltage. The power counter register (SD_PWCNT) is
shown in

Figure 9-37

and described in

Table 9-19

.

Figure 9-37. Power Counter Register (SD_PWCNT)

31

16

15

0

Reserved

PWRCNT

R-0

R/W-0

LEGENDR/W = Read/Write; R = Read only; -n = value after reset

Table 9-19. Power Counter Register (SD_PWCNT) Field Descriptions

Bit

Field

Value

Description

31-16

Reserved

0

These bits are initialized to zero, and writes to them are ignored. Reads return 0.

15-0

PWRCNT

Power counter register. This register is used to introduce a delay between the PAD ACTIVE
pin assertion and the command issued.

0

No additional delay added

1h

TCF delay (card clock period)

2h

TCF x 2 delay (card clock period)

FFFEh

TCF x 65534 delay (card clock period)

FFFFh

TCF x 65535 delay (card clock period)

9.4.10 SDMA System Address (SD_SDMASA)

This register is used to program a counter to delay command transfers after activating the PAD power.
This value depends on PAD characteristics and voltage. The SDMA System address (SD_SDMASA) is
shown in

Figure 9-34

and described in

Table 9-16

.

Figure 9-38. Card Status Response Error (SD_SDMASA)

31

0

SDMA_SYSADDR

R-0

LEGENDR/W = Read/Write; R = Read only; -n = value after reset

Table 9-20. Card Status Response Error (SD_SDMASA) Field Descriptions

Bit

Field

Value

Description

31-0

SDMA_SYSADDR

This register contains the system memory address for a SDMA transfer. When the Host
Controller stops a SDMA transfer, this register shall point to the system address of the next
contiguous data position. It can be accessed only if no transaction is executing (i.e., after a
transaction has stopped).

Read operations during transfers may return an invalid value. The Host Driver shall initialize this
register before starting a SDMA transaction. After SDMA has stopped, the next system address
of the next contiguous data position can be read from this register.

The SDMA transfer waits at the every boundary specified by the Host SDMA Buffer Boundary in
the Block Size register. The Host Controller generates DMA Interrupt to request the Host Driver
to update this register. The Host Driver sets the next system address of the next data position
to this register. When the most upper byte of this register (003h) is written, the Host Controller
restarts the SDMA transfer. When restarting SDMA by the Resume command or by setting
Continue Request in the Block Gap Control register, the Host Controller shall start at the next
contiguous address stored here in the SDMA System Address register. ADMA does not use this
register.

973

SPRUGX9 – 15 April 2011

Secure Digital (SD)/—Secure Digital I/O (SDIO) Card Interface

Submit Documentation Feedback

© 2011, Texas Instruments Incorporated

Содержание TMS320C6A816 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6A816 Series

Eaton PKE-COM-RTU Instruction Leaflet preview
PKE-COM-RTU
Бренд: Eaton Страницы: 2
Eaton i-on30R Installation Instructions preview
i-on30R
Бренд: Eaton Страницы: 2
Eaton MEMSHIELD 4 Installation Instructions Manual preview
MEMSHIELD 4
Бренд: Eaton Страницы: 8
GAI-Tronics Elemec3 013-02-0095-002 Manual preview
Elemec3 013-02-0095-002
Бренд: GAI-Tronics Страницы: 12
U-Prox MP LTE User Manual preview
MP LTE
Бренд: U-Prox Страницы: 3
U-Prox MP LTE Quick Start Manual preview
MP LTE
Бренд: U-Prox Страницы: 2
Water Specialist WS2H Manual preview
WS2H
Бренд: Water Specialist Страницы: 60
Parker EP Series Pro-Bloc Installation And Operation Manual preview
EP Series Pro-Bloc
Бренд: Parker Страницы: 11
Parker MT-700 Series Installer'S Manual preview
MT-700 Series
Бренд: Parker Страницы: 22
Parker HASV08R Quick Start Manual preview
HASV08R
Бренд: Parker Страницы: 2
schmersal AES 1175 Operating Instructions Manual preview
AES 1175
Бренд: schmersal Страницы: 6
Pangolin FB4 Series User Manual preview
FB4 Series
Бренд: Pangolin Страницы: 35
Continental Instruments CICP1800T Datasheet preview
CICP1800T
Бренд: Continental Instruments Страницы: 2
OmarLift HEVOS HE650 Operating Instructions Manual preview
HEVOS HE650
Бренд: OmarLift Страницы: 50
M-system R7ML-EC16A Instruction Manual preview
R7ML-EC16A
Бренд: M-system Страницы: 3
Marmitek W home TM13AU Manual preview
W home TM13AU
Бренд: Marmitek Страницы: 4
Avenview SW-HBT4K-C6-4X4E Quick Start Manual preview
SW-HBT4K-C6-4X4E
Бренд: Avenview Страницы: 8
Berker funkbus Operating Instructions Manual preview
funkbus
Бренд: Berker Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды