manualshive.com logo in svg

Texas Instruments TMS320C6A816 Series, Техническое справочное руководство


Поделиться
Скачать
background image

Preliminary

www.ti.com

EDMA and EDMA Events

1.9

EDMA and EDMA Events

1.9.1 Overview

The device uses L3 crossbar architecture to control access between device processors, subsystems, and
peripherals. It includes four third-party DMA transfer controllers (TPTCs) that provide four EDMA channels
for transfer between L3 slaves. The device also makes use of the third-party channel controller (TPCC).
The TPCC provides a user and event interface to the EDMA system. It includes up to 64 event channels
to which all system synchronization events can be mapped and 8 auto-submit channels (QDMA).

Parameter RAM: Each EDMA is specified by an 8-word (32-byte) parameter table contained in Parameter
RAM (PaRAM) within the TPCC. The number of PaRAM entries supported is 512.

QDMA: The quick DMA (QDMA) function is contained within the TPCC. The device implements all 8
possible QDMA channels. Each QDMA channel has a selectable PaRAM entry used to specify the
transfer. A QDMA transfer is submitted immediately upon writing of the “trigger” parameter (as opposed to
the occurrence of an event as with EDMA). The QDMA parameter RAM may be written by any bus master
with an L3 connection to the TPCC CFG port.

1.9.2 EDMA Regions

In order to support multiple processors, the TPCC is configured with all eight interrupt regions
implemented. This allows each processing element (Cortex-A8, DSP, and Media Controller) to be
interrupted upon completion of any EDMAs associated with its program flow independent of other EDMAs
in the system. Assignment of the region interrupts is shown in

Table 1-66

.

Table 1-66. EDMA Regions

TPCC Region

Processor

Interrupt Name (Processor)

0

Cortex-A8

CCINT0

1

–

–

1

DSP

CCINT1

2

–

–

3

–

–

4

Media Controller 0

CCINT4

5

Media Controller 1

CCINT5

6

–

–

7

–

–

1.9.3 Synchronization Events

The EDMA supports up to 64 EDMA channels that service peripheral devices and external
memory.

Table 1-67

lists the source of EDMA synchronization events associated with each of the

programmable EDMA channels. The association of an event to a channel is fixed; each of the EDMA
channels has one specific event associated with it. These specific events are captured in the EDMA event
registers (ER, ERH) even if the events are disabled by the EDMA event enable registers (EER, EERH).
For more detailed information on the EDMA module and how EDMA events are enabled, captured,
processed, linked, chained, and cleared, see the Enhanced DMA (EDMA) Controller User's Guide.

179

SPRUGX9 – 15 April 2011

Chip Level Resources

Submit Documentation Feedback

© 2011, Texas Instruments Incorporated

Содержание TMS320C6A816 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6A816 Series

Hamworthy AM1 Installation, Commissioning, Operation & Service Instructions preview
AM1
Бренд: Hamworthy Страницы: 10
Walchem W100 Troubleshooting Manual preview
W100
Бренд: Walchem Страницы: 10
Manfrotto 851 Instructions Manual preview
851
Бренд: Manfrotto Страницы: 16
Gardena EasyPlus Operator'S Manual preview
EasyPlus
Бренд: Gardena Страницы: 14
Gardena 1273 Operating Instructions preview
1273
Бренд: Gardena Страницы: 4
NAD C 399 Addendum Sheet preview
C 399
Бренд: NAD Страницы: 4
NAD C388 Addendum Sheet preview
C388
Бренд: NAD Страницы: 4
Sanhua DPF Series Instructions preview
DPF Series
Бренд: Sanhua Страницы: 3
QED MP50 Instruction Manual preview
MP50
Бренд: QED Страницы: 26
B&G ZEUS S Detailed App Manual preview
ZEUS S
Бренд: B&G Страницы: 19
Panasonic KX-A16B Quick Start Manual preview
KX-A16B
Бренд: Panasonic Страницы: 8
Gardigo 62318 Instruction Manual preview
62318
Бренд: Gardigo Страницы: 6
VAT 244 Series Installation, Operating, & Maintenance Instructions preview
244 Series
Бренд: VAT Страницы: 14
DSE DSE 6120 Installation Instructions preview
DSE 6120
Бренд: DSE Страницы: 2
Aulisa GA-AP0011 Instructions For Use Manual preview
GA-AP0011
Бренд: Aulisa Страницы: 32
YASKAWA J1000 CIMR-JC series Option Manual preview
J1000 CIMR-JC series
Бренд: YASKAWA Страницы: 26
Tech 21 MIDI MONGOOSE Owner'S Manual preview
MIDI MONGOOSE
Бренд: Tech 21 Страницы: 2
Jeckson Electric 47-1010A-T Owner'S Manual preview
47-1010A-T
Бренд: Jeckson Electric Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды