manualshive.com logo in svg

Texas Instruments TMS320C6201, Справочное руководство


Поделиться
Скачать
background image

Overview of TMS320C6000 Peripherals

1-11

Introduction

EMIF: The EMIF supports a glueless interface to several external devices, in-
cluding:

-

Synchronous burst SRAM (SBSRAM)

-

Synchronous DRAM (SDRAM)

-

Asynchronous devices, including SRAM, ROM, and FIFOs

-

An external shared-memory device

Boot Configuration: The TMS320C62x and TMS320C67x provide a variety
of boot configurations that determine what actions the DSP performs after de-
vice reset to prepare for initialization. These include loading in code from an
external ROM space on the EMIF and loading code through the HPI/expan-
sion bus from an external host.

McBSP: The multichannel buffered serial port (McBSP) is based on the stan-
dard serial port interface found on the TMS320C2000 and ’C5000 platform de-
vices. In addition, the port can buffer serial samples in memory automatically
with the aid of the DMA/EDMA controller. It also has multichannel capability
compatible with the T1, E1, SCSA, and MVIP networking standards. Like its
predecessors, it provides:

-

Full-duplex communication

-

Double-buffered data registers that allow a continuous data stream

-

Independent framing and clocking for receive and transmit

-

Direct interface to industry-standard codecs, analog interface chips
(AICs), and other serially connected A/D and D/A devices

In addition, the McBSP has the following capabilities:

-

Direct interface to:

J

T1/E1 framers

J

ST-BUS

t

 compliant devices

J

IOM-2 compliant devices

J

AC97 compliant devices

J

IIS compliant devices

J

SPI

 devices

-

Multichannel transmission and reception of up to 128 channels

-

A wider selection of data sizes including 8-, 12-, 16-, 20-, 24-, and 32-bits

-

µ

-law and A-law companding

-

8-bit data transfers with LSB or MSB first

-

Programmable polarity for both frame synchronization and data clocks

-

Highly programmable internal clock and frame generation

Содержание TMS320C6201






























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320C6201

D-Link DES-1210-08P Manual preview
DES-1210-08P
Бренд: D-Link Страницы: 15
National Instruments NI 9426 Getting Started Manual preview
NI 9426
Бренд: National Instruments Страницы: 17
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Бренд: Moxa Technologies Страницы: 2
Ubiquiti UniFi Cloud Key Quick Start Manual preview
UniFi Cloud Key
Бренд: Ubiquiti Страницы: 13
Supersonic Franky Instruction Manual preview
Franky
Бренд: Supersonic Страницы: 46
ETAS XETK-S22.0 User Manual preview
XETK-S22.0
Бренд: ETAS Страницы: 84
EZCast Pro Dongle II D10 Repair Manual preview
Dongle II D10
Бренд: EZCast Pro Страницы: 4
ekwb EK-FC R9-295X2 Installation And Mounting Manual preview
EK-FC R9-295X2
Бренд: ekwb Страницы: 2
Variscite VAR-SOM-MX8M-PLUS Quick Start Manual preview
VAR-SOM-MX8M-PLUS
Бренд: Variscite Страницы: 2
ETAS XETK-S21.0B User Manual preview
XETK-S21.0B
Бренд: ETAS Страницы: 68
ExtraHop EDA 4200 Install preview
EDA 4200
Бренд: ExtraHop Страницы: 2
Buffalo LinkStation 500 User Manual preview
LinkStation 500
Бренд: Buffalo Страницы: 139
SIIG SATA II-150 PCI Quick Installation Manual preview
SATA II-150 PCI
Бренд: SIIG Страницы: 16
IceManCooler ICE-SKY-E User Manual preview
ICE-SKY-E
Бренд: IceManCooler Страницы: 2
R3 Bridge E User Manual preview
Bridge E
Бренд: R3 Страницы: 48
Stepper Motor Canada DB25-1R5AM Manual preview
DB25-1R5AM
Бренд: Stepper Motor Canada Страницы: 7
QNAP QSW-3216R-8S8T Quick Installation Manual preview
QSW-3216R-8S8T
Бренд: QNAP Страницы: 11
Qorvo QPE6105A Manual preview
QPE6105A
Бренд: Qorvo Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды