manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

14.6.2.15 I2C FIFO Receive (I2CFFRX) Register (Offset = 21h) [reset = 0h]

The I2C receive FIFO register (I2CFFRX) is a 16-bit register that contains the control and status bits for the 
receive FIFO mode of operation on the I2C peripheral.

Figure 14-33. I2C FIFO Receive (I2CFFRX) Register

15

14

13

12

11

10

9

8

RESERVED

RXFFRST

RXFFST

R-0h

R/W-0h

R-0h

7

6

5

4

3

2

1

0

RXFFINT

RXFFINTCLR

RXFFIENA

RXFFIL

R-0h

R-0/W1S-0h

R/W-0h

R/W-0h

Table 14-24. I2C FIFO Receive (I2CFFRX) Register Field Descriptions

Bit

Field

Type

Reset

Description

15-14

RESERVED

R

0h

Reserved

13

RXFFRST

R/W

0h

I2C receive FIFO reset bit
Reset type: SYSRSn
0h (R/W) = Reset the receive FIFO pointer to 0000 and hold the 
receive FIFO in the reset state.
1h (R/W) = Enable the receive FIFO operation.

12-8

RXFFST

R

0h

Contains the status of the receive FIFO:
xxxxx Receive FIFO contains xxxxx bytes
00000 Receive FIFO is empty.
Reset type: SYSRSn

7

RXFFINT

R

0h

Receive FIFO interrupt flag.
This bit cleared by a CPU write of a 1 to the RXFFINTCLR bit. If the 
RXFFIENA bit is set, this bit will generate an interrupt when it is set
Reset type: SYSRSn
0h (R/W) = Receive FIFO interrupt condition has not occurred.
1h (R/W) = Receive FIFO interrupt condition has occurred.

6

RXFFINTCLR

R-0/W1S

0h

Receive FIFO interrupt flag clear bit.
Reset type: SYSRSn
0h (R/W) = Writes of zeros have no effect. Reads return a zero.
1h (R/W) = Writing a 1 to this bit clears the RXFFINT flag.

5

RXFFIENA

R/W

0h

Receive FIFO interrupt enable bit.
Reset type: SYSRSn
0h (R/W) = Disabled. RXFFINT flag does not generate an interrupt 
when set.
1h (R/W) = Enabled. RXFFINT flag does generate an interrupt when 
set.

4-0

RXFFIL

R/W

0h

Receive FIFO interrupt level.
These bits set the status level that will set the receive interrupt flag. 
When the RXFFST4-0 bits reach a value equal to or greater than 
these bits, the RXFFINT flag is set. This will generate an interrupt if 
the RXFFIENA bit is set.
Note: Since these bits are reset to zero, the receive FIFO interrupt 
flag will be set if the receive FIFO operation is enabled and the I2C 
is taken out of reset. This will generate a receive FIFO interrupt if 
enabled. To avoid this, modify these bits on the same instruction as 
or prior to setting the RXFFRST bit. Because the I2C on this device 
has a 4-level receive FIFO, these bits cannot be configured for an 
interrupt of more than 4 FIFO levels.
Reset type: SYSRSn

Inter-Integrated Circuit Module (I2C)

www.ti.com

876

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

LAUNDRY SOLUTION SX205100A User Manual preview
SX205100A
Бренд: LAUNDRY SOLUTION Страницы: 14
Nations N32G43 Series User Manual preview
N32G43 Series
Бренд: Nations Страницы: 654
Vais Technology SoundLinQ SL2xD2 Owner'S Manual preview
SoundLinQ SL2xD2
Бренд: Vais Technology Страницы: 21
D+H KA 66-TW-DF Original Instructions Manual preview
KA 66-TW-DF
Бренд: D+H Страницы: 16
Tekvox TCX7 Installation Manual preview
TCX7
Бренд: Tekvox Страницы: 2
Open Grow GroLab TankBot Installation Manual preview
GroLab TankBot
Бренд: Open Grow Страницы: 20
AMX NetLinx NXI Operation/Reference Manual preview
NetLinx NXI
Бренд: AMX Страницы: 26
Omega PHCN-37 Quick Start Up Manual preview
PHCN-37
Бренд: Omega Страницы: 2
SR Aquaristik Dual Stage CO2 REGULATOR Assembly Instruction Manual preview
Dual Stage CO2 REGULATOR
Бренд: SR Aquaristik Страницы: 5
EBECO EB-Connect WiFi Manual preview
EB-Connect WiFi
Бренд: EBECO Страницы: 24
Zenty ZT-117 User Manual preview
ZT-117
Бренд: Zenty Страницы: 50
SmartKing PA240510 User Manual preview
PA240510
Бренд: SmartKing Страницы: 1
Hyster E40ZS Manual preview
E40ZS
Бренд: Hyster Страницы: 25
Martek Chicken Switch K-15 User Manual preview
Chicken Switch K-15
Бренд: Martek Страницы: 9
TAEHA PROCON-100 Operation Manual preview
PROCON-100
Бренд: TAEHA Страницы: 70
Koganei FRZB Series Manual preview
FRZB Series
Бренд: Koganei Страницы: 36
Robo-Tank Basic User Manual preview
Basic
Бренд: Robo-Tank Страницы: 70
Infranor Xtracontrol DC2 User Manual preview
Xtracontrol DC2
Бренд: Infranor Страницы: 87

Бренды по названию

Популярные бренды

Загрузить еще бренды