manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

MADDF32 MRd, MRe, MRf ||MMOV32 MRa, mem32

32-Bit Floating-Point Addition with Parallel Move

Operands

MRd

CLA floating-point destination register for the MADDF32 (MR0 to 
MR3).
MRd cannot be the same register as MRa.

MRe

CLA floating-point source register for the MADDF32 (MR0 to MR3)

MRf

CLA floating-point source register for the MADDF32 (MR0 to MR3)

MRa

CLA floating-point destination register for the MMOV32 (MR0 to 
MR3).
MRa cannot be the same register as MRd.

mem32

32-bit memory location accessed using one of the available 
addressing modes. This is the source for the MMOV32.

Opcode

LSW: mmmm mmmm mmmm mmmm 

MSW: 0001 ffee ddaa addr

Description

Perform an MADDF32 and a MMOV32 operation in parallel. Add MRf to the contents 
of MRe and store the result in MRd. In parallel move the contents of the 32-bit location 
mem32 to MRa.

MRd = MRe + MRf; 

MRa = [mem32];

Restrictions

The destination register for the MADDF32 and the MMOV32 must be unique. That is, 
MRa and MRd cannot be the same register.

Flags

This instruction modifies the following flags in the MSTF register:

Flag

TF

ZF

NF

LUF

LVF

Modified

No

Yes

Yes

Yes

Yes

The MSTF register flags are modified as follows:
• LUF = 1 if MADDF32 generates an underflow condition.
• LVF = 1 if MADDF32 generates an overflow condition.

The MMOV32 Instruction will set the NF and ZF flags as follows:

NF = MRa(31); 

ZF = 0; 

if(MRa(30:23) == 0) { ZF = 1; NF = 0; };

Pipeline

The MADDF32 and the MMOV32 both complete in a single cycle.

www.ti.com

Control Law Accelerator (CLA)

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

TMS320x2806x Microcontrollers

601

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Falcon RS500 Owner'S And Installer'S Manual preview
RS500
Бренд: Falcon Страницы: 3
IFM Electronic ecomat 100 R 360 Operating Instructions Manual preview
ecomat 100 R 360
Бренд: IFM Electronic Страницы: 16
IFM Electronic AC1331 Installation Instructions Manual preview
AC1331
Бренд: IFM Electronic Страницы: 23
Zener SMARTSTART 6000 Networking Manual preview
SMARTSTART 6000
Бренд: Zener Страницы: 36
Zapi SMART CONSOLE Instructions preview
SMART CONSOLE
Бренд: Zapi Страницы: 5
POLA HP49 Handbook preview
HP49
Бренд: POLA Страницы: 2
ICP DAS USA ISaGRAF WinCE ViewPAC User Manual preview
ISaGRAF WinCE ViewPAC
Бренд: ICP DAS USA Страницы: 192
AGRI TRONIX DIGI-STAR GT400 Operator'S Manual preview
DIGI-STAR GT400
Бренд: AGRI TRONIX Страницы: 26
Beckhoff CX8080 Documentation preview
CX8080
Бренд: Beckhoff Страницы: 67
Omron K8AK-LS Manual preview
K8AK-LS
Бренд: Omron Страницы: 12
Texas Instruments LaunchPad LP-CC1352P7-1 Manual preview
LaunchPad LP-CC1352P7-1
Бренд: Texas Instruments Страницы: 3
OCTANORM M 1497-4 User Manual preview
M 1497-4
Бренд: OCTANORM Страницы: 6
Hanna Instruments BL121 Manual preview
BL121
Бренд: Hanna Instruments Страницы: 44
Texas Instruments TIDA-00830 Quick Start Manual preview
TIDA-00830
Бренд: Texas Instruments Страницы: 6
Canford TECPRO HS581 Manual preview
TECPRO HS581
Бренд: Canford Страницы: 2
Magnetek IMPULSE G+ Series 3 Instruction Manual preview
IMPULSE G+ Series 3
Бренд: Magnetek Страницы: 9
Carrier WSHP Open v3 Integration Manual preview
WSHP Open v3
Бренд: Carrier Страницы: 58
Full Gauge Controls MT-514e Manual preview
MT-514e
Бренд: Full Gauge Controls Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды