manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

•

One-Shot (OSHT):

 When a one-shot trip event occurs, the action specified in the TZCTL[TZA] and 

TZCTL[TZB] bits is carried out immediately on the EPWMxA and/or EPWMxB output. 

Table 3-18

 lists the 

possible actions. In addition, the one-shot trip event flag (TZFLG[OST]) is set and a EPWMx_TZINT interrupt 
is generated if it is enabled in the TZEINT register and PIE peripheral. The one-shot trip condition must be 
cleared manually by writing to the TZCLR[OST] bit.

If the one-shot interrupt is enabled via the TZEINT register, and DCAEVT1 or DCBEVT1 are selected as 
OSHT trip sources via the TZSEL register, it is not necessary to also enable the DCAEVT1 or DCBEVT1 
interrupts in the TZEINT register, as the DC events trigger interrupts through the OSHT mechanism.

•

Digital Compare Events (DCAEVT1/2 and DCBEVT1/2):

 A digital compare DCAEVT1/2 or DCBEVT1/2 

event is generated based on a combination of the DCAH/DCAL and DCBH/DCBL signals as selected by the 
TZDCSEL register. The signals which source the DCAH/DCAL and DCBH/DCBL signals are selected via the 
DCTRIPSEL register and can be either trip zone input pins or analog comparator COMPxOUT signals. For 
more information on the digital compare submodule signals, see 

Section 3.2.9

.

When a digital compare event occurs, the action specified in the TZCTL[DCAEVT1/2] and 
TZCTL[DCBEVT1/2] bits is carried out immediately on the EPWMxA and/or EPWMxB output. 

Table 3-18

 lists 

the possible actions. In addition, the relevant DC trip event flag (TZFLG[DCAEVT1/2] / TZFLG[DCBEVT1/2]) 
is set and a EPWMx_TZINT interrupt is generated if it is enabled in the TZEINT register and PIE peripheral.

The specified condition on the pins is automatically cleared when the DC trip event is no longer present. 
The TZFLG[DCAEVT1/2] or TZFLG[DCBEVT1/2] flag bit will remain set until it is manually cleared by 
writing to the TZCLR[DCAEVT1/2] or TZCLR[DCBEVT1/2] bit. If the DC trip event is still present when the 
TZFLG[DCAEVT1/2] or TZFLG[DCBEVT1/2] flag is cleared, then it will again be immediately set.

The action taken when a trip event occurs can be configured individually for each of the ePWM output pins by 
way of the TZCTL register bit fields. One of four possible actions, shown in 

Table 3-18

, can be taken on a trip 

event.

Table 3-18. Possible Actions On a Trip Event

TZCTL Register Bit Settings

EPWMxA and/or

EPWMxB

Comment

0,0

High-Impedance

Tripped

0,1

Force to High State

Tripped

1,0

Force to Low State

Tripped

1,1

No Change

Do Nothing.

No change is made to the output.

 

Enhanced Pulse Width Modulator (ePWM) Module

www.ti.com

288

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

ABATEC A1 Installation And Operation Instruction Manual preview
A1
Бренд: ABATEC Страницы: 8
Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Бренд: Panasonic Страницы: 45
Panasonic Minas A4 Series Connection Manual preview
Minas A4 Series
Бренд: Panasonic Страницы: 5
Fagor CNC 8070 Programming Manual preview
CNC 8070
Бренд: Fagor Страницы: 556
hager coviva Smartbox TKP100A Quick Manual preview
coviva Smartbox TKP100A
Бренд: hager Страницы: 4
Vag ZETA Operating And Maintenance Instructions Manual preview
ZETA
Бренд: Vag Страницы: 12
Rain Bird PAR+ES Installation Manual preview
PAR+ES
Бренд: Rain Bird Страницы: 24
Rain Bird ESP-LXIVM Series Device Installation Manuallines preview
ESP-LXIVM Series
Бренд: Rain Bird Страницы: 16
Vaillant VRT 350f Installation Instructions Manual preview
VRT 350f
Бренд: Vaillant Страницы: 36
Vaillant VRT 350 Installation Instructions Manual preview
VRT 350
Бренд: Vaillant Страницы: 28
Vaillant VAZ CPC Operating Instructions Manual preview
VAZ CPC
Бренд: Vaillant Страницы: 92
Valcom V-1092 User Manual preview
V-1092
Бренд: Valcom Страницы: 3
Valcom V-1092 Technical Specifications preview
V-1092
Бренд: Valcom Страницы: 2
RadioMaster MT12 Quick Start Manual preview
MT12
Бренд: RadioMaster Страницы: 10
YASKAWA PROFINET V1000 Technical Manual preview
PROFINET V1000
Бренд: YASKAWA Страницы: 49
M-system MSP10 Instruction Manual preview
MSP10
Бренд: M-system Страницы: 17
Cooper S225-50-45 Service Information preview
S225-50-45
Бренд: Cooper Страницы: 4
Anritsu NF7600 Series Operation Manual preview
NF7600 Series
Бренд: Anritsu Страницы: 74

Бренды по названию

Популярные бренды

Загрузить еще бренды