manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

17.5.46 USB External Power Control Register (USBEPC), offset 0x400

The USB external power control 32-bit register (USBEPC) specifies the function of the two-pin external power 
interface (USB0EPEN and USB0PFLT). The assertion of the power fault input may generate an automatic 
action, as controlled by the hardware configuration registers. The automatic action is necessary because the 
fault condition may require a response faster than one provided by firmware.

Mode(s):

Host

Device

USBEPC is shown in 

Figure 17-58

 and described in 

Table 17-61

.

Figure 17-58. USB External Power Control Register (USBEPC)

31

10

9

8

Reserved

PFLTACT

R-0

R/W-0

7

6

5

4

3

2

1

0

Reserved

PFLTAEN

PFLTSEN

PFLTEN

Reserved

EPENDE

EPEN

R-0

R/W-0

R/W-0

R/W-0

R-0

R/W-0

R/W-0

LEGEND: R/W = Read/Write; -

n

 = value after reset

Table 17-61. USB External Power Control Register (USBEPC) Field Descriptions

Bit

Field

Value

Description

31-10

Reserved

0

Reserved

9-8

PFLTACT

Power Fault Action. This bit field specifies how the USB0EPEN signal is changed when detecting a 
USB power fault.

0h

Unchanged. USB0EPEN is controlled by the combination of the EPEN and EPENDE bits.

1h

Tristate. USB0EPEN is undriven (tristate).

2h

Low. USB0EPEN is driven Low.

3h

High. USB0EPEN is driven High.

7

Reserved

0

Reserved

6

PFLTAEN

Power Fault Action Enable. This bit specifies whether a USB power fault triggers any automatic 
corrective action regarding the driven state of the USB0EPEN signal.

0

Disabled. USB0EPEN is controlled by the combination of the EPEN and EPENDE bits.

1

Enabled. The USB0EPEN output is automatically changed to the state specified by the PFLTACT field.

5

PFLTSEN

Power Fault Sense. This bit specifies the logical sense of the USB0PFLT input signal that indicates an 
error condition.
The complementary state is the inactive state.

0

Low Fault. If USB0PFLT is driven Low, the power fault is signaled internally (if enabled by the PFLTEN 
bit).

1

High Fault. If USB0PFLT is driven High, the power fault is signaled internally (if enabled by the 
PFLTEN bit).

4

PFLTEN

Power Fault Input Enable. This bit specifies whether the USB0PFLT input signal is used in internal 
logic.

0

Not Used. The USB0PFLT signal is ignored.

1

Used. The USB0PFLT signal is used internally

3

Reserved

0

Reserved

Universal Serial Bus (USB) Controller

www.ti.com

1128

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Jetline 9600 Series Operation Manual preview
9600 Series
Бренд: Jetline Страницы: 58
Magnescale LY71 Manual preview
LY71
Бренд: Magnescale Страницы: 3
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Бренд: Yamaha Страницы: 92
Zamel Extra Free RZB-02 Quick Manual preview
Extra Free RZB-02
Бренд: Zamel Страницы: 2
IBM MTM 2145-SV1 Hardware Installation Manual preview
MTM 2145-SV1
Бренд: IBM Страницы: 214
Netro SPRITE Quick Start Manual preview
SPRITE
Бренд: Netro Страницы: 14
Sonos Controller CR100 Brochure & Specs preview
Controller CR100
Бренд: Sonos Страницы: 2
Brooks GF100 Series Installation And Operation Manual preview
GF100 Series
Бренд: Brooks Страницы: 68
D+H DXD 150-K-BSY+ Original Instructions Manual preview
DXD 150-K-BSY+
Бренд: D+H Страницы: 20
Doepke RJSG 1 Installation And Operating Manual preview
RJSG 1
Бренд: Doepke Страницы: 2
RADEMACHER Troll Comfort Instruction Manual For The Electrical Connection And For Commissioning preview
Troll Comfort
Бренд: RADEMACHER Страницы: 112
Newport i/8 Quick Start preview
i/8
Бренд: Newport Страницы: 2
Infineon Technologies CYPRESS Traveo S6J335 Series Manual preview
CYPRESS Traveo S6J335 Series
Бренд: Infineon Technologies Страницы: 308
Aerotech ABL9000 Series User Manual preview
ABL9000 Series
Бренд: Aerotech Страницы: 36
Ohio Medical Push-To-Set PTS-CVR Service Manual preview
Push-To-Set PTS-CVR
Бренд: Ohio Medical Страницы: 25
CLS LDV-45 Manual preview
LDV-45
Бренд: CLS Страницы: 6
ZiLOG S3F8S19 User Manual preview
S3F8S19
Бренд: ZiLOG Страницы: 23
Yaesu G-5500DC Instruction Manual preview
G-5500DC
Бренд: Yaesu Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды