manualshive.com logo in svg

Texas Instruments TMS320 2806 Series, Техническое справочное руководство


Поделиться
Скачать
background image

16.4 eCAN Controller Overview

The eCAN has an internal 32-bit architecture.

The eCAN module consists of:
• The CAN protocol kernel (CPK)
• The message controller comprising:

– The memory management unit (MMU), including the CPU interface and the receive control unit 

(acceptance filtering), and the timer management unit

– Mailbox RAM enabling the storage of 32 messages
– Control and status registers

After the reception of a valid message by the CPK, the receive control unit of the message controller determines 
if the received message must be stored into one of the 32 message objects of the mailbox RAM. The receive 
control unit checks the state, the identifier, and the mask of all message objects to determine the appropriate 
mailbox location. The received message is stored into the first mailbox passing the acceptance filtering. If the 
receive control unit could not find any mailbox to store the received message, the message is discarded.

A message is composed of an 11- or 29-bit identifier, a control field, and up to 8 bytes of data.

When a message must be transmitted, the message controller transfers the message into the transmit buffer of 
the CPK in order to start the message transmission at the next bus-idle state. When more than one message 
must be transmitted, the message with the highest priority that is ready to be transmitted is transferred into the 
CPK by the message controller. If two mailboxes have the same priority, then the mailbox with the higher number 
is transmitted first.

The timer management unit comprises a time-stamp counter and apposes a time stamp to all messages 
received or transmitted. It generates an interrupt when a message has not been received or transmitted during 
an allowed period of time (time-out). The time-stamping feature is available in eCAN mode only.

To initiate a data transfer, the transmission request bit (TRS.n) must be set. The entire transmission procedure 
and possible error handling are then performed without any CPU involvement. If a mailbox has been configured 
to receive messages, the CPU easily reads its data registers using CPU read instructions. The mailbox may be 
configured to interrupt the CPU after every successful message transmission or reception.

16.4.1 Standard CAN Controller (SCC) Mode

The SCC Mode is a reduced functionality mode of the eCAN. Only 16 mailboxes (0 through 15) are available in 
this mode. The time stamping feature is not available and the number of acceptance masks available is reduced. 
This mode is selected by default. The SCC mode or the full featured eCAN mode is selected using the SCB bit 
(CANMC.13).

Controller Area Network (CAN)

www.ti.com

1004

TMS320x2806x Microcontrollers

SPRUH18I – JANUARY 2011 – REVISED JUNE 2022

Submit Document Feedback

Copyright © 2022 Texas Instruments Incorporated

Содержание TMS320 2806 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TMS320 2806 Series

Galcon 61 Series Installation And Operating Instructions Manual preview
61 Series
Бренд: Galcon Страницы: 35
Gamma Vacuum SPCe User Manual preview
SPCe
Бренд: Gamma Vacuum Страницы: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Бренд: Gamma Страницы: 28
Acuity Controls nLight ECLYPSE Safety Instructions preview
nLight ECLYPSE
Бренд: Acuity Controls Страницы: 5
Bard CompleteStat-Series CS9B-THO Product Manual preview
CompleteStat-Series CS9B-THO
Бренд: Bard Страницы: 2
Woodward ProAct III Installation And Operation Manual preview
ProAct III
Бренд: Woodward Страницы: 32
Danfoss 087H3803 Installation Manual preview
087H3803
Бренд: Danfoss Страницы: 20
B&R Automation PC 810 User Manual preview
Automation PC 810
Бренд: B&R Страницы: 428
Evco EVCLC229N9E Manual preview
EVCLC229N9E
Бренд: Evco Страницы: 78
Zennio MAXinBOX 24 ZIO-MB24 User Manual preview
MAXinBOX 24 ZIO-MB24
Бренд: Zennio Страницы: 24
ISC APECS Operational Instructions preview
APECS
Бренд: ISC Страницы: 20
Computherm PS Gate User Manual preview
PS Gate
Бренд: Computherm Страницы: 40
Pellet Grill Outlet 180-LV Installation Instructions And User Manual preview
180-LV
Бренд: Pellet Grill Outlet Страницы: 4
WAREMA BACnet 4M230.8I AP Installation Instructions preview
BACnet 4M230.8I AP
Бренд: WAREMA Страницы: 4
POLA HD38 Handbook preview
HD38
Бренд: POLA Страницы: 7
LOVATO ELECTRIC ATL800 Installation Manual preview
ATL800
Бренд: LOVATO ELECTRIC Страницы: 6
ZIEHL-ABEGG Acontrol PSET6 Operating Instructions Manual preview
Acontrol PSET6
Бренд: ZIEHL-ABEGG Страницы: 24
HANYOUNG NUX TPR-3M Instruction Manual preview
TPR-3M
Бренд: HANYOUNG NUX Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды