Texas Instruments TIDA-050026-23882, Руководство по конструкции

Страница: 4 / 24

System Overview
www.ti.com
4 TIDA032 – October 2019
Submit Documentation Feedback
Copyright © 2019, Texas Instruments Incorporated
24-Port (2 pair) Power Sourcing Equipment Reference Design for Multi-port
Applications
2.2.2 Communication Interface
2.2.2.1 PSE I
2
C Communication
The board provides two I
2
C interfaces communicating to PSE:
1. J10 on the motherboard (PSEMTHR24EVM-081) provides I
2
C access to all PSE devices directly. The
TPS2388x GUI can communicate to PSE devices with the USB2ANY interface adapter.
2. J11 and J12 on the motherboard (PSEMTHR24EVM-081) provides I
2
C access and system control
signal to the MSP430 daughtercard.
2.2.2.2 MCU - Host Communication
The MSP430 daughtercard provides I
2
C/UART communication port to host through J12 to J14 on MSP430
daughtercard (PSEMCUDAUEVM-082). The PSE system GUI provides host configurations to the PSE
system.
Host interface user's guide can be accessed from TIDA-050026-23882 folder or PSEMCUDAUEVM-082
tool folder .
2.2.3 MSP430F523x Hardware Design
Table 2. MSP430 GPIO Pin Assignment
PIN NUMBER
MSP430F5234 (48RGZ)
TERMINAL FUNCTION COMMENT
COMMUNICATION
22 P3.0 I
2
C SDA USCI_B0 I
2
C to PSEs
23 P3.1 I
2
C SCL USCI_B0 I
2
C to PSEs
30 P4.1 I
2
C SDA USCI_B1 I
2
C to host
31 P4.2 I
2
C SCL USCI_B1 I
2
C to host
33 P4.4 UART TX USCI_A1 UART to host (debug only)
34 P4.5 UART RX USCI_A1 UART to host (debug only)
21 P2.7 SPI CLK USCI_A0 SPI to host (reserved)
24 P3.2 SPI slave TX enable, USCI_A0 SPI to host (reserved)
25 P3.3 UART TX,USCI_A0 or SPI
slave in, master out UART to host TX or SPI to host (reserved)
26 P3.4 UART RX, USCI_A0 or SPI
slave out, master in UART to host RX or SPI to host (reserved)
HARDWARE INTERRUPT
13 P1.0 PSE INT Connect to PSE INT pin
16 P1.3 OC Alert Connect to external current sensing circuit if not
used, connect to 3.3 V
18 P1.5 Power supply 1 Connect to power supply 1 power good signal. In
RPS mode, P1.5 must be connected to main power
supply.
If there's only one power supply, the
power good signal must be connected to P1.5.
19 P1.6 Power supply 2 Connect to power supply 2 power good signal, if not
used, connect to GND. In RPS mode, P1.6 must be
connected to backup power supply
20 P1.7 Disable all ports This is for hardware disable ports(Reserved)
GENERAL I/O
4 P5.0 RESET PSE RESET Connect to PSE RESET pin
17 P1.4 OSS PSE OSS Connect to PSE OSS pin
46 P6.0 Interrupt pin to host
35 P4.6 BSL mode indication to host MCU configures as output. If MCU is in BSL mode,
output high. If in normal operation mode, output low.
48 P6.2 Guard-band indication Need an external LED