background image

EVM Setup and Operation

www.ti.com

8

SLLU296 – August 2018

Submit Documentation Feedback

Copyright © 2018, Texas Instruments Incorporated

TCAN1046V Evaluation Module

Table 4. Protection and Filtering Configuration (continued)

Configuration

Footprint Reference

Use Case

Population and Description

C1/C6 or D1

Transient and ESD protection

To add extra protection for system
level transients and ESD
protection, TVS diode population
option via D1 footprint or varistor
population via C1/C6 footprint.

C9/C15 or D2

To add extra protection for system
level transients and ESD
protection, TVS diode population
option via D2 footprint or varistor
population via C9/C15 footprint.

2.3

Using Customer Installable I/O Options for Current Limiting, Pullup and Pulldown,
Noise Filtering

The CAN EVM has footprints on the PCB for the installation of various filtering and protection options to
adapt the EVM to match CAN network topology requirements if the EVM is being used as a CAN node.

Each digital input or output pin has footprints allowing for series current-limiting resistors (default
populated with 0

Ω

), pull-up or -down resistors (depending on pin use), and a capacitor to GND which

allows for RC filters when configured with a series resistor.

Table 5

lists these features for each of the

digital input and output pins of the EVM. Replace or populate the RC components as necessary for the
application.

Table 5. RC Filter and Protection Lists

Device Pin

Jumperable

Series R

Pullup and

Pulldown

C to GND

No.

Description

Type

Pullup

Pulldown

1/6

TXD1/TXD2

Input

N/A

N/A

R14/R19

R12/R24 PU

C8/C14

4/7

RXD1/RXD2

Output

N/A

N/A

R17/R23

R13/R24 PU

C10/C13

3

CAN EVM Configuration for TCAN1046V (Factory Installed)

The TCAN1046V device interfaces CAN protocol controllers with the physical bus in accordance to the
ISO 11898 standard. This device is compatible with the ISO 11898 High Speed CAN (Controller Area
Network) Physical Layer standards: 11898-2. This device is designed for use of up to 5 Mbit CAN
systems, and it includes many protection features providing device and CAN network robustness.

Содержание TCAN1046V















Отзывы: