manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Техническое справочное руководство, Страница: 1717 / 1817

Поделиться
Скачать
Texas Instruments SimpleLink Ethernet MSP432E401Y Скачать руководство пользователя страница 1717

www.ti.com

USB Registers

1717

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

Universal Serial Bus (USB) Controller

27.5.14 USBCCONF Register (Offset = 0x61) [reset = 0x0]

USB Common Configuration (USBCCONF)

OTG A / Host

OTG B / Device

The USBCCONF register is an 8-bit register that contains various common configuration bits. These bits
include the RX/TX early DMA enable bits.

USBCCONF is shown in

Figure 27-19

and described in

Table 27-24

.

Return to

Summary Table

.

Figure 27-19. USBCCONF Register

7

6

5

4

3

2

1

0

RESERVED

TXEDMA

RXEDMA

R-0x0

R/W-0x0

R/W-0x0

Table 27-24. USBCCONF Register Field Descriptions

Bit

Field

Type

Reset

Description

7-2

RESERVED

R

0x0

1

TXEDMA

R/W

0x0

TX Early DMA Enable.

0x0 = Late Mode: DMAREQ signal for all IN endpoints is deasserted
when the MAXP bytes have been written to an endpoint.

0x1 = Early Mode: DMAREQ signal for all IN endpoints is deasserted
when MAXP-8 bytes have been written to an endpoint.

0

RXEDMA

R/W

0x0

TX Early DMA Enable.

0x0 = Late Mode: DMAREQ signal for all OUT endpoints is
deasserted when the MAXP bytes have been read to an endpoint.

0x1 = Early Mode: DMAREQ signal for all OUT endpoints is
deasserted when MAXP-8 bytes have been read to an endpoint.

Содержание SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов