manualshive.com logo in svg

Texas Instruments OMAP36 Series, Техническое справочное руководство


Поделиться
Скачать
background image

MPU INTCPS

Modem INTC

TWL4030

External

device

GPIO 1

sys_nirq

Device

M_IRQ_7

M_IRQ_[34:29]

MD_IRQ_[13:10]

External

device

(Not in standalone configuration)

to

GPIO 6

MD_IRQ_0

Power IC

intc-002

MPU subsystem

Public Version

Interrupt Controller Environment

www.ti.com

12.2 Interrupt Controller Environment

The INTC can handle two types of interrupts originating from an external device:

•

sys_nirq interrupt inputs:
The MPU INTC and modem INTC handle external interrupts through a dedicated sys_nirq interrupt line
that connects the two INTC modules with a TWL4030 power IC, respectively. An interrupt can
generate a system wake-up event.
If the system is idle and the external interrupt is masked, the interrupt cannot wake up the system. Like
other interrupt lines, the external interrupt is active at low level and is acknowledged by the software
according to the common programming model.

NOTE:

If the CORE power domain is in retention (CSWR or OSWR) or off mode, the interrupt

requests (internal or external), the MPU INTC, and the modem INTC (in the CORE domain)
have no effect. The CORE power domain does not wake up, and the interrupt is not signaled
to the MPU/modem.

•

GPIO interrupt inputs:
External devices can also use GPIO modules to generate interrupts to the MPU and the modem. There
are six dedicated interrupt lines to the MPU INTC and four dedicated interrupt inputs to the modem
INTC. One interrupt line is associated with each GPIO module. Each GPIO module can generate a
single interrupt whenever there is at least one event in any one of the configured 32 GPIO inputs. For
more information about GPIO features, see

Chapter 25

, General-Purpose Interface.

Figure 12-2

shows the relationship between the device and external interrupts.

Figure 12-2. Interrupts From External Devices

NOTE:

The modem INTC cannot use GPIO5 and GPIO6 as interrupt sources.

The features specific to INTCPS are:
•

Up to 96 level-sensitive interrupt inputs

•

Individual priority (up to 64) for each interrupt input

•

Interrupt lines connected to internal module interrupts

•

One incoming interrupt line from an external device

2406

Interrupt Controller

SWPU177N – December 2009 – Revised November 2010

Copyright © 2009–2010, Texas Instruments Incorporated

Содержание OMAP36 Series



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMAP36 Series

B2 ABB2050 Instruction Manual preview
ABB2050
Бренд: B2 Страницы: 52
Paradyne 3172 Quick Reference preview
3172
Бренд: Paradyne Страницы: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Бренд: Paradyne Страницы: 2
Multitech MultiConnect SE MTS2EA Quick Start Manual preview
MultiConnect SE MTS2EA
Бренд: Multitech Страницы: 8
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Бренд: Garland Страницы: 43
Datasat DDR-16 AES67 Installation And Operating Manual preview
DDR-16 AES67
Бренд: Datasat Страницы: 24
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Бренд: Dahua Страницы: 33
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Бренд: ZoneVu Страницы: 15
FUNcube Dongle Pro User Manual preview
Dongle Pro
Бренд: FUNcube Страницы: 23
Comway 4G DTU Configuration Instructions preview
4G DTU
Бренд: Comway Страницы: 20
Promise Technology VTrak J310S Quick Start Manual preview
VTrak J310S
Бренд: Promise Technology Страницы: 26
Vega ARIES v3.0 Product Reference Manual preview
ARIES v3.0
Бренд: Vega Страницы: 12
Corsair LL140 RGB Series Manual preview
LL140 RGB Series
Бренд: Corsair Страницы: 30
ADTRAN 1200864L1 Quick Start Manual preview
1200864L1
Бренд: ADTRAN Страницы: 2
Aim ACE1553-3U-4 Hardware Manual preview
ACE1553-3U-4
Бренд: Aim Страницы: 35
WTI NPS-16HD20-1 User Manual preview
NPS-16HD20-1
Бренд: WTI Страницы: 178
PairGain HiGain Line Unit HLU-388 Quick Installation Manual preview
HiGain Line Unit HLU-388
Бренд: PairGain Страницы: 7
NUROTRON CS-10A Operation Manual preview
CS-10A
Бренд: NUROTRON Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды