Texas Instruments Jacinto 7 DRA829 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 55

background image

Resource

nRSTOUT_SOC

TPS65941213-Q1

PMIC

Delay Diagram

Total Delay

Rail Name

0 us

H_SOC_PORz_1V8

nRSTOUT_SOC

TPS65941213-Q1

200 us

H_SOC_PORz_1V8

Figure 6-5. ESM_SOC_ERROR Sequence

6.3.5 PWR_SOC_ERROR

In the event of an error on any of the power rails which are part of the SOC power rail group, the
PWR_SOC_ERROR sequence is performed. The nRSTOUT_SOC pin is pulled low and the SOC power rails
execute a normal processor power down sequence except the MCU power group remains energized as shown
in

. The state of the I2C_7 trigger in both PMICs determines whether the DDR supplies and control

signal remain energized (I2C_7=1) or disabled (I2C_7=0), as shown in

.

In the start of the sequence the following instructions are executed:

// TPS65941213

// Set AMUXOUT_EN and CLKMON_EN, clear LPM_EN and nRSTOUT_SOC

REG_WRITE_MASK_IMM ADDR=0x81 DATA=0x18 MASK=0xE1

// Clear SPMI_LPM_EN

REG_WRITE_MASK_IMM ADDR=0x82 DATA=0x00 MASK=0xEF

//TPS65941111

// Set AMUXOUT_EN and CLKMON_EN, clear LPM_EN

REG_WRITE_MASK_IMM ADDR=0x81 DATA=0x18 MASK=0xE3

// Clear SPMI_LPM_EN

REG_WRITE_MASK_IMM ADDR=0x82 DATA=0x00 MASK=0xEF

Resource

PMIC

Delay Diagram

Total Delay

Rail Name

nRSTOUT_SOC

TPS65941213-Q1

0 us

H_SOC_PORz_1V8

LDO3

TPS65941213-Q1

2500 us

VDD_DLL_0V8

BUCK123

TPS65941213-Q1

2500 us

VDD_CPU(AVS)

BUCK5

TPS65941213-Q1

3000 us

VDD_PHY_1V8

BUCK5

TPS65941111-Q1

500 us

VDD_RAM_0V85

LDO3

TPS65941111-Q1

500 us

VDD_IO_1V8

BUCK1234

TPS65941111-Q1

2500 us

VDD_CORE_0V8

LDO4

TPS65941111-Q1

3000 us

VDA_PLL_1V8

LDO1

TPS65941111-Q1

3500 us

VDD_SD_DV

LDO2

TPS65941111-Q1

3500 us

VDD_USB_3V3

Figure 6-6. PWR_SOC_ERROR with I2C_7 High in both PMICs

Pre-Configurable Finite State Machine (PFSM) Settings

SLVUC99 – JANUARY 2022

Submit Document Feedback

Optimized Dual TPS6594-Q1 PMIC User Guide for Jacinto

™

7 DRA829 or

TDA4VM Automotive PDN-0C

41

Copyright © 2022 Texas Instruments Incorporated

«
...
39
40
41
42
43
...
»

Содержание Jacinto 7 DRA829
























































Отзывы:

Нет отзывов

Похожие инструкции для Jacinto 7 DRA829

Бренд: Baicells Страницы: 8

Бренд: Data Translation Страницы: 60

Бренд: TC Electronic Страницы: 55

Бренд: Freescale Semiconductor Страницы: 921

Бренд: Measurement Computing Страницы: 27

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 3

Scorpio WD2500BPVT

Бренд: Western Digital Страницы: 4

Бренд: RAK Страницы: 30

Бренд: Hauppauge Страницы: 62

Бренд: SriHome Страницы: 12

Бренд: Baikal Miner Страницы: 14

Бренд: Stepper Motor Canada Страницы: 5

CloudGen Firewall

Бренд: Barracuda Страницы: 8

ExtremeCloud Appliance E1120

Бренд: Extreme Networks Страницы: 219

Бренд: Datalogic Страницы: 2

Бренд: Foxconn Страницы: 1

Бренд: IBM Страницы: 44

Бренд: Ezquest Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды