Texas Instruments ISO154 EVM Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 20

Texas Instruments ISO154 EVM Series Скачать руководство пользователя страница 6

J1

J2

U2

J3A/J4A

J5A/J6A

J3B/J4B

J5B/J6B

J7A/J8A

J9A/J10A

J7B/J8B

J9B/J10B

Power Supply

VCC1

Power Supply

VCC2

I C Transmitter

2

or

Oscilloscope

I C Transmitter

2

U1

Oscilloscope

or

EVM Setup and Operation

2

EVM Setup and Operation

This section includes the setup and operation of the EVM for parameter performance evaluation. Typical
input and output waveforms are included.

2.1

Overview

The basic setup in

has the two power supplies required to evaluate isolator performance with any

combination of 3.3 V or 5 V on either side. If both sides are evaluated at the same supply voltage, only
one power supply is required and can be used to power both sides of the EVM.

CAUTION

Note that this EVM is for operating parameter performance evaluation only and
not designed for isolation voltage testing. Any voltage applied above the 5.5-V
maximum recommended operating voltage of the isolators may damage the
EVM.

Please note that if the ISO1541 is used, providing an input signal on the SCL2 pin does not yield any
output on SCL1, SCL1 remains pulled up to VCC1.

Figure 4. Basic EVM Operation

6

SLLU166 – June 2012

ISO154xEVM Low-Power Bidirectional I

2

C Isolators Evaluation Module

Submit Documentation Feedback

Copyright © 2012, Texas Instruments Incorporated

«
...
4
5
6
7
8
...
»

Содержание ISO154 EVM Series





















Отзывы:

Нет отзывов