Texas Instruments INA220EVM Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 26

Texas Instruments INA220EVM Скачать руководство пользователя страница 15

INA220 Software Overview

15

SBOU079B – July 2009 – Revised May 2016

Submit Documentation Feedback

Copyright © 2009–2016, Texas Instruments Incorporated

INA220 Evaluation Module

4.1

INA220EVM Software Install

Follow these steps to install the INA220EVM software:

Step 1.

Software can be downloaded from the

web page, or from the disk included with

the INA220EVM, which contains a folder called

Install_software

/.

Step 2.

Find the file called

setup.exe

. Double-click the file to start the installation process.

Step 3.

Follow the on-screen prompts to install the software.

Step 4.

To remove the application, use the Windows Control Panel utility,

Add/Remove Software

.

The

INA220 Quick-Start Video

(included with the kit, or available for download in the INA220 product

folder) gives more detail regarding the initialization of the software.

4.2

Starting the INA220EVM Software

The INA220 software can be operated through the Windows

Start

menu. From Start, select

All Programs

;

then select the

INA220EVM

program.

shows how the software should appear if the EVM is

functioning properly.

Figure 10. INA220EVM Software—Functioning Properly

«
...
13
14
15
16
17
...
»

Содержание INA220EVM



























Отзывы:

Нет отзывов