manualshive.com logo in svg

Texas Instruments EMIF16, Руководство пользователя

Поделиться
Скачать
Texas Instruments EMIF16 Скачать руководство пользователя страница 42

4.8 Interrupt Raw Register (IRR)

4-8

KeyStone Architecture External Memory Interface (EMIF16) User Guide

SPRUGZ3A—May 2011

Submit Documentation Feedback 

Chapter 4—Registers

www.ti.com

4.8 Interrupt Raw Register (IRR)

The interrupt bits in the Interrupt Raw Register are set after the corresponding 
interrupt condition occurs, regardless of whether the interrupt has been enabled or 
disabled. The IRR is shown in 

Figure 4-4

 and 

Table 4-5

.

Figure 4-4

Interrupt Raw Register (IRR)

31

6

5

2

1

0

Reserved

WR

Reserved

AT

R - 0x0

RW - 0x0

R - 0x0

RW - 0x0

Table 4-5

Interrupt Raw Register (IRR) Details

Bit

Field

Reset Value

Description

31-6

Reserved

0x0

Reserved. The reserved bit location is always read as 0. A value written to this field has no effect

5-2

WR

0x0

Wait Rise.

Set to 1 by hardware to indicate rising edge on the corresponding EMIFWAIT pin has been detected. 

The WP0-1 bits in the Async Wait Cycle Config register have no effect on these bits.

Writing a 1 will clear these bits as well as the WR_MASKED bits in the Interrupt Masked register. Writing 
a 0 has no effect.

1

Reserved

0x0

Reserved. The reserved bit location is always read as 0. A value written to this field has no effect

0

AT

0x0

Asynchronous  Timeout.

Set to 1 by hardware to indicate that during an extended asynchronous memory access cycle, the WAIT 
signal did not go inactive within the number of cycles defined by the MAX_EXT_WAIT field in Async 
Wait Cycle Config register. 

Writing a 1 will clear this bit as well as the AT_MASKED bit in the Interrupt Masked register. Writing a 0 
has no effect.

End of Table 4-5

Содержание EMIF16
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды