manualshive.com logo in svg

Texas Instruments EMIF16, Руководство пользователя

Поделиться
Скачать
Texas Instruments EMIF16 Скачать руководство пользователя страница 12

2.1 EMIF16 Signal Descriptions

2-2

KeyStone Architecture External Memory Interface (EMIF16) User Guide

SPRUGZ3A—May 2011

Submit Documentation Feedback 

Chapter 2—Architecture

www.ti.com

2.1 EMIF16 Signal Descriptions

A basic block diagram of the EMIF16 asynchronous interface is shown in 

Figure 2-1

. 

Table 2-1

 below lists the asynchronous signals of the EMIF16 module. 

Figure 2-1

Basic Block diagram for EMIF16

Table 2-1

EMIF16 Signal Descriptions

Pin

Description

EMIFD [15:0]

Data I/O. Input for data reads and output for data writes.

EMIFA [23:0]

External address output.

EMIFCE0

External CE0 chip select. Active-low chip select for CE space 0.

EMIFCE1

External CE1 chip select. Active-low chip select for CE space 1.

EMIFCE2

External CE2 chip select. Active-low chip select for CE space 2.

EMIFCE3

External CE3 chip select. Active-low chip select for CE space 3.

EMIFBE[1:0]

Byte enables.

EMIFWAIT [1:0]

Used to insert wait states into the memory cycle.

EMIFWE

Write enable - active low during a write transfer strobe period

EMIFOE

Output enable-active low during the entire period of a read access.

EMIFRnW

Read-write enable

End of Table 2-1

EMIFD [15:0]

EMIFA [23:0]

EMIFCE [3:0]

            EMIFBE [1:0]

External

Memory

EMIFWE

Interface

(EMIF16)

     EMIFOE

          EMIFWAIT [1:0]

EMIFRnW

Содержание EMIF16
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды