Texas Instruments DS90UB954-Q1EVM Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 67

Texas Instruments DS90UB954-Q1EVM Скачать руководство пользователя страница 7

3.4 DS90UB954-Q1EVM Setup

1. Use the mini USB to USB cable to connect J2 to computer USB port for register programming and open

Analog LaunchPAD. See

for details on installing and using Analog LaunchPAD.

2. Configure jumpers J8, J10, J11, J15, J16, J23, J27 to set device’s operating modes. The default

configuration can be seen in

3. Configure Power-over-Coax power supplies for RX0 and RX1 with J18 and J17 respectively.
4. Connect the DS90UB954-Q1EVM to DS90UB953-Q1EVM (or variant) to RX0 and/or DS90UB933-Q1EVM

to RX1 using a coax cable.

5. Interface MIPI CSI-2 output signals (J24) to test equipment or host processor (optional, not required to check

status of FPD-Link III connection between serializer and deserializer).

6. Provide power to board. TI recommends using current limited bench supply to provide power to J1 (barrel

jack) or J3.

4 DS90UB954-Q1EVM Board Configuration

4.1 Default Configuration

Default jumper placement is shown in red below. The

schematic page also illustrates the default

jumper positions. This configuration sets the device into the following mode:
• Device is set for FPD-Link III inputs from coax in CSI mode (for DS90UB953-Q1EVM (or variant))
• VDDIO is set to 1.8V
• VDD5V is powered by the 5V LDO
• The 3.3V + 1.1V LDO (U10) is powered by VDD5V
• The 9V LDO for PoC for RX0 and RX1 are enabled

Figure 4-1. DS90UB954-Q1EVM with Jumpers Highlighted

Quick Start Guide

SNLU223C – AUGUST 2017 – REVISED NOVEMBER 2022

Submit Document Feedback

DS90UB954-Q1EVM Deserializer User's Guide

7

Copyright © 2022 Texas Instruments Incorporated

«
...
5
6
7
8
9
...
»

Содержание DS90UB954-Q1EVM




































































Отзывы:

Нет отзывов