Texas Instruments DS90UB954-Q1EVM Скачать руководство пользователя страница 12

Страница: 12 / 67

4.7 Control Interface

Table 4-7. VDDIO Interface Header - J16

Reference

Signal

Description

J16

VDDIO

Selects VDDIO bus voltage

Short pins 1-2: 3.3V IO (Default)

Short pins 2-3: 1.8V IO

Table 4-8. GPIO Interface Header - J22

Reference

Signal

Description

J22.1

GPIO0

General Purpose Input/Output 0

J22.3

GPIO1

General Purpose Input/Output 1

J22.5

GPIO2

General Purpose Input/Output 2

J22.7

GPIO3/INTB

General Purpose Input/Output 3 / Interrupt (Active Low).
Pulled up to VDDIO by 4.7kΩ

J22.9

GPIO4

General Purpose Input/Output 4

J22.11

GPIO5

General Purpose Input/Output 5

J22.13

GPIO6

General Purpose Input/Output 6

J22.15

EN 25MHz

Enable/Disable 25MHz Oscillator

Table 4-9. CMLOUT Output Signals

Reference

Signal

Description

TP16

CMLOUTP

Test Pad for Channel Monitor Loop-through Driver

TP17

CMLOUTN

Test Pad for Channel Monitor Loop-through Driver

Table 4-10. FPD-Link III Mode Control- J15

Reference

Mode

(1)

Description

J15.1

CSI Mode (DS90UB953-Q1 compatible)

(2)

J15.2

RAW12 / LF (DS90UB933 compatible)

J15.3

RAW12 / HF (DS90UB933 compatible)

J15.4

RAW10 (DS90UB933 compatible)

(1)

Only set one ON.

(2)

This function is only available with 2-MP ADAS chipsets.

Table 4-11. Device Mode Control - J11

Reference

Signal

Input = L

Input = H

Description

J11.1

BISTEN

For Normal operation (Default)

Test Mode enable

Test Mode

J11.2

RSVD

Tied to GND (Default)

N/A

Reserved

J11.3

VDD_SEL

Internal 1.1V regulator from

1.8V supply (Default)

1.1V is supplied to VDD1V1

pins

VDD 1.1V Source Select

J11.4

PDB

Device is powered down

Device is enabled (Default)

Power-down Mode

DS90UB954-Q1EVM Board Configuration

www.ti.com

DS90UB954-Q1EVM Deserializer User's Guide

SNLU223C – AUGUST 2017 – REVISED NOVEMBER 2022

Submit Document Feedback

Содержание DS90UB954-Q1EVM




































































Результаты поиска

Содержание DS90UB954-Q1EVM

Отзывы:

Texas Instruments DS90UB954-Q1EVM, Руководство пользователя, Страница: 12 / 67

Результаты поиска

Содержание DS90UB954-Q1EVM

Отзывы: