Texas Instruments CDCE72010 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

Texas Instruments CDCE72010 Скачать руководство пользователя страница 7

www.ti.com

TI CDCE72010 Control GUI Interface

Step 2: Primary/Secondary Reference Input Selection

The primary or the secondary reference input buffer section on the GUI can be clicked for a popup window
that opens up, as shown in the following illustration. This illustration shows selections on the external input
signal type (differential or single ended), the external signal connection to the CDCE72010
primary/secondary inputs (AC or DC termination), input buffer internal termination (enabled or disabled),
input buffer VBB voltage polarity (normal or inverted), input buffer hysteresis, and fail-safe mode (enabled
or disabled).

Step 3: Reference Input Selection through Smart MUX

The Smart MUX section of the GUI can be clicked for a popup window that opens up as displayed in the
following illustration, showing selections of Primary, Secondary, Auto ( with Primary preference), and
None.

SLAU250 – May 2008

1.5-GHz Low-Phase Noise Clock Evaluation Board

7

Submit Documentation Feedback

«
...
5
6
7
8
9
...
»

Содержание CDCE72010





















Отзывы:

Нет отзывов