Texas Instruments CC112 Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 109

Texas Instruments CC112 Series Скачать руководство пользователя страница 15

CC112X/CC1175

SWRU295C

Page 15 of 108

Address

Strobe
Name

Description

0x30

SRES

Reset chip

0x31

SFSTXON

Enable and calibrate frequency synthesizer (if

SETTLING_CFG.FS_AUTOCAL = 1

).

If in RX and

PKT_CFG2.CCA_MODE

≠ 0: Go to a wait state where only the synthesizer is running

(for quick RX/TX turnaround).

0x32

SXOFF

Enter XOFF state when CSn is de-asserted

0x33

SCAL

Calibrate frequency synthesizer and turn it off.

SCAL

can be strobed from IDLE mode without

setting manual calibration mode (

SETTLING_CFG.FS_AUTOCAL = 0

)

0x34

SRX

Enable RX. Perform calibration first if coming from IDLE and

SETTLING_CFG.FS_AUTOCAL = 1

0x35

STX

In IDLE state: Enable TX. Perform calibration first if

SETTLING_CFG.FS_AUTOCAL = 1

.

If in RX state and

PKT_CFG2.CCA_MODE

≠ 0: Only go to TX if channel is clear

0x36

SIDLE

Exit RX/TX, turn off frequency synthesizer and exit eWOR mode if applicable

0x37

SAFC

Automatic Frequency Compensation

0x38

SWOR

Start automatic RX polling sequence (eWOR) as described in Section 8.6 if

WOR_CFG0.RC_PD = 0

0x39

SPWD

Enter SLEEP mode when CSn is de-asserted

0x3A

SFRX

Flush the RX FIFO. Only issue

SFRX

in IDLE or RX_FIFO_ERR states

0x3B

SFTX

Flush the TX FIFO. Only issue

SFTX

in IDLE or TX_FIFO_ERR states

0x3C

SWORRST

Reset the eWOR timer to the Event1 value

0x3D

SNOP

No operation. May be used to get access to the chip status byte

Table 6: Command Strobes

A command strobe may be followed by any other SPI access without pulling CSn high, and the
command strobes are executed immediately. This applies for all command strobes except

SPWD

,

SWOR

, and the

SXOFF

strobe.

When a

SRES

strobe is issued the CSn pin must be kept low and wait for SO to go low again before

the next header byte can be issued, as shown in Figure 5.

SI

Header

SRES

Header

Addr

Data

SO

CSn

x

Figure 5: SRES Command Strobe

The

, and the

command strobes are not executed before the CSn goes high.

3.2.3

Direct FIFO Access

The complete RX and TX FIFOs, with associated pointers, are mapped in the register space for FIFO
manipulation  and  SW-debug  purposes.  The  FIFOs  are  mapped  as  shown  in  Table  7  (the  address
must  be  preceded  by  the  command  0x3E)  while  the  FIFO  pointers  are  located  in  extended  register
space (address 0xD2 - 0xD5, see Table 5).

Direct FIFO Access Mapping

Retention

0x00 - 0x7F

TXFIFO

No

0x80 - 0xFF

RXFIFO

No

Table 7: Direct FIFO Access Mapping

«
...
13
14
15
16
17
...
»

Содержание CC112 Series














































































































Отзывы:

Нет отзывов