Texas Instruments bq77905 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 21

Texas Instruments bq77905 Скачать руководство пользователя страница 4

bq77905EVM Quick Start Guide

4

SLVUAN2A – May 2016 – Revised July 2016

Submit Documentation Feedback

Copyright © 2016, Texas Instruments Incorporated

bq77905 3-5S Low Power Protector Evaluation Module

10. Remove the shunt at the J3 C position to simulate a cold condition. Observe that the pack voltage

drops to approximately 0 V and returns to normal when the shunt is re-installed.

11. Adjust the supply voltage to 12 V to simulate an undervoltage condition. Observe that the pack voltage

drops to approximately 0 V.

12. Adjust the supply voltage to 18 V to allow recovery from the undervoltage condition. Observe that the

pack voltage remains at approximately 0 V with the load resistor in place.

13. Remove the load resistor on the PACK terminals. Observe that the pack voltage returns to the supply

voltage because undervoltage recovers on the installed part configuration with both voltage and load
removal.

14. Disable the power supply and disconnect, if complete.

«
...
2
3
4
5
6
...
»

Содержание bq77905






















Отзывы:

Нет отзывов