Texas Instruments BQ25181 Скачать руководство пользователя страница 5

Страница: 5 / 24

2 EVM Connectors and Test Points

Table 2-1

shows the default configuration for connectors.

Table 2-1. Jumper Default Configuration

Jumper Name

Description

Setting

C Pullup

VIN and GND connector

VBAT and GND connector

Battery pack connector

TS potentiometer connector

Connected

USB2ANY connector

VIO connector to 3p3V

Connected

J8, J9

Board connector to other modules

J10

LED jumper

Connected

J11

VSYS and GND connector

J13

Charge enable jumper control

Low

J14

Micro USB connector (optional for VIN)

Table 2-2

describes the test points available on the board for easy access measurement.

Table 2-2. Test Point Descriptions

Test Point

Description

TP1, TP2, TP3

IC GND test point

TP4

IC /CE test point

TP5

IC VIN test point

TP6

IC VSYS test point

TP7

IC SCL test point

TP8

IC VBAT test point

TP9

IC SDA test point

TP10

IC /PG or GPO test point

TP11

IC TS/MR test point

TP12

IC /INT test point

www.ti.com

EVM Connectors and Test Points

SLUUCL3 – APRIL 2022

Submit Document Feedback

BQ25181 EVM User's Guide

Содержание BQ25181
























Результаты поиска

Содержание BQ25181

Отзывы:

Похожие инструкции для BQ25181

Бренды по названию

Популярные бренды

Texas Instruments BQ25181, Руководство пользователя

Результаты поиска

Содержание BQ25181

Отзывы:

Похожие инструкции для BQ25181

Бренды по названию

Популярные бренды