background image

www.ti.com

Introduction

3

SLUUC73 – March 2020

Submit Documentation Feedback

Copyright © 2020, Texas Instruments Incorporated

BQ25616, BQ25616J BMS026 Evaluation Module

Table 3. EVM Jumper, Shunt and Switch Installation (continued)

Jack

Description

BQ25616 Setting

BQ25616J Setting

JP6

Micro B USB input D+ connection to charger
D+ pin

Installed

Installed

JP7

ICHG to BAT or BATTERY connection

Not Installed

Not Installed

JP8

ICHG resistor setting connection. Must be
connected for charging to operate correctly.

Installed

Installed

JP9

Micro B USB input D+ connection to charger
D+ pin

Installed

Installed

JP10

PSEL pin input current selection. Connect this
to HIGH on PSEL enabled chargers to select
500mA default input current limit. Connect
this to LOW on PSEL enabled chargers to
select 2.4-A default input current limit

Not Installed

Not Installed

JP11

REGN connection to TS network. Must be
connected for thermistor sensing to operate
correctly.

Installed

Installed

JP12

ILIM resistor setting connection. Must be
connected for ‘Unknown Adapter’ input
current limiting to operate correctly.

Installed

Installed

JP13

STAT pin LED indicator connection. This
indicates the current charger Status

Installed

Installed

JP14

/PG pin LED indicator connection. On /PG
enabled chargers, this indicates the Power
Good status

Installed

Installed

JP15

ICHG, ILIM, AGND header connection point.

Not Installed

Not Installed

JP16

Thermistor NORMAL temperature setting.
Connect jumper to simulate charger entering
TNORMAL (T2-T3) temperature region.

Installed

Installed

JP17

/CE pin connection to ground to enable
charging. When removed, /CE pin will pull up
to disable charge

Installed

Installed

JP18

Thermistor HOT temperature setting. Connect
jumper to simulate charger entering THOT
(>T5) temperature region.

Not Installed

Not Installed

JP19

D- to /PG rail connection

Not Installed

Not Installed

JP20

OTG pin connection to ground to disable OTG
boost mode. When removed, OTG boost
mode is enabled only in battery-only
operation

Installed

Installed

JP21

VSET pin setting connection. Leave floating
to set VBATREG to 4.208V. Connect to 10-
kOhm to ground to set VBATREG to 4.100V.
Connect to ground directly to set VBATREG
to 4.352V

Not Installed

Not Installed

S1

/QON pin pull-down. No function.

Not Populated

Not Populated

S2

STAT and /PG LED bypass switches

1-4: Open, 2-3: Open

1-4: Open, 2-3: Open

Table 4

lists the recommended operating conditions for this EVM.

Table 4. Recommended Operating Conditions

Symbol

Description

MIN

TYP

MAX

Unit

V

VBUS

, V

VAC

Input voltage applied to VAC and VBUS pins

4.0

13.5

V

V

BAT

Battery voltage applied to BAT pin

4.35

V

I

VBUS

Input current into VBUS

3.2

A

I

SW

Output current (SW)

3.2

A

I

BAT

Fast charging current

3.0

A

RMS Discharging current through internal
BATFET

6.0

A

Содержание BMS026

























Отзывы: