Texas Instruments AMC7832EVM Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 33

Texas Instruments AMC7832EVM Скачать руководство пользователя страница 13

AMC7832EVM Software Overview

13

SLAU544A – February 2014 – Revised September 2016

Submit Documentation Feedback

Copyright © 2014–2016, Texas Instruments Incorporated

AMC7832EVM User’s Guide

5

AMC7832EVM Software Overview

This section discusses how to use the AMC7832EVM software.

5.1

Starting the AMC7832EVM Software

After the hardware connections are established and jumper settings configured, launch the software
located in the AMC7832EVM folder of the Start All Programs menu, and select the AMC7832EVM icon.

Figure 8. AMC7832EVM GUI Location

If the SDM-USB-DIG is properly connected to the AMC7832EVM, the GUI should automatically power on
the system and display

CONNECTED: Power On

in the upper right area of the GUI (see

Figure 9. AMC7832EVM GUI – Power On

If the SDM-USB-DIG has a faulty connection, or is not connected at all, the GUI launches in simulation
mode. In simulation mode,

NOT CONNECTED: Simulating

is displayed in the top right area of the GUI. If

this text appears while the SDM-USB-DIG device is connected, then unplug the SDM-USB-DIG and close
the GUI. Reconnect the SDM-USB-DIG, and ensure that the connectors are correctly aligned. After doing
those steps, verify the USB extender cable is properly connected to both the SDM-USB-DIG and PC, and
relaunch the GUI. This issue can also occur if the CDC driver is installed incorrectly. The AMC7832EVM
software may need to be reinstalled.

«
...
11
12
13
14
15
...
»

Содержание AMC7832EVM


































Отзывы:

Нет отзывов