Texas Instruments AM1808 Скачать руководство пользователя страница 703

Страница: 703 / 1820

www.ti.com

Registers

703

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

Enhanced Direct Memory Access (EDMA3) Controller

17.4.3.6.13 Destination FIFO Options Register n (DFOPTn)

The destination FIFO options register

(DFOPT

) is shown in

Figure 17-103

and described in

Table 17-86

Figure 17-103. Destination FIFO Options Register n (DFOPTn)

Reserved

TCCHEN

Rsvd

TCINTEN

Reserved

TCC

R-0

R/W-0

R-0

R/W-0

R-0

R/W-0

TCC

Rsvd

FWID

Rsvd

PRI

Reserved

DAM

SAM

R/W-0

R-0

R/W-0

R-0

R/W-0

R-0

R/W-0 R/W-0

LEGEND: R/W = Read/Write; R = Read only; -

= value after reset

Table 17-86. Destination FIFO Options Register n (DFOPTn) Field Descriptions

Bit

Field

Value

Description

31-23

Reserved

TCCHEN

Transfer complete chaining enable.

Transfer complete chaining is disabled.

Transfer complete chaining is enabled.

Reserved

TCINTEN

Transfer complete interrupt enable.

Transfer complete interrupt is disabled.

Transfer complete interrupt is enabled.

19-18

Reserved

17-12

TCC

0-3Fh

Transfer complete code. This 6-bit code is used to set the relevant bit in CER or IPR of the EDMA3CC.

Reserved

10-8

FWID

0-7h

FIFO width. Applies if either SAM or DAM is set to constant addressing mode.

FIFO width is 8 bits.

FIFO width is 16 bits.

FIFO width is 32 bits.

FIFO width is 64 bits.

FIFO width is 128 bits.

5h-7h

Reserved

6-4

PRI

0-7h

Transfer priority.

Priority 0 - Highest priority

1h-6h

Priority 1 to priority 6

Priority 7 - Lowest priority

3-2

Reserved

DAM

Destination address mode within an array.

Increment (INCR) mode. Destination addressing within an array increments.

Constant addressing (CONST) mode. Destination addressing within an array wraps around upon
reaching FIFO width.

SAM

Source address mode within an array.

Increment (INCR) mode. Source addressing within an array increments.

Constant addressing (CONST) mode. Source addressing within an array wraps around upon reaching
FIFO width.

Содержание AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AM1808

Отзывы:

Бренды по названию

Популярные бренды

Texas Instruments AM1808, Техническое справочное руководство

Результаты поиска

Содержание AM1808

Отзывы:

Бренды по названию

Популярные бренды