Texas Instruments AM1808 Скачать руководство пользователя страница 278

Страница: 278 / 1820

SYSCFG Registers

www.ti.com

278

SPRUH82C – April 2013 – Revised September 2016

Submit Documentation Feedback

System Configuration (SYSCFG) Module

10.5.21 Deep Sleep Register (DEEPSLEEP)

The deep sleep register (DEEPSLEEP) control the Deep Sleep logic. See your device-specific data
manual and the

Boot Considerations

chapter for details on boot and configuration settings. The

DEEPSLEEP is shown in

Figure 10-48

and described in

Table 10-52

Figure 10-48. Deep Sleep Register (DEEPSLEEP)

SLEEPENABLE

SLEEPCOMPLETE

Reserved

R/W-0

R-0

SLEEPCOUNT

R/W-FFFFh

LEGEND: R/W = Read/Write; R = Read only; -

= value after reset

Table 10-52. Deep Sleep Register (DEEPSLEEP) Field Descriptions

Bit

Field

Value

Description

SLEEPENABLE

Deep sleep enable.

The software must clear this bit to 0 when the device is awakened from

deep sleep.

Device is in normal operating mode; DEEPSLEEP pin has no effect.

Deep sleep mode is enabled; setting DEEPSLEEP pin low initiates oscillator shut down.

SLEEPCOMPLETE

Deep sleep complete.

Once the deep sleep process starts, the software must poll the

SLEEPCOMPLETE bit; when the SLEEPCOMPLETE bit is read as 1, the software should
clear the SLEEPENABLE bit and continue operation.

SLEEPCOUNT delay is not complete.

SLEEPCOUNT delay is complete.

29-16

Reserved

15-0

SLEEPCOUNT

0-FFFFh

Deep sleep counter.

Number of cycles to count prior to the oscillator being stable. All 16

bits are tied directly to the counter in the Deep Sleep logic.

Содержание AM1808





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание AM1808

Отзывы:

Texas Instruments AM1808, Техническое справочное руководство, Страница: 278 / 1820

Результаты поиска

Содержание AM1808

Отзывы: