background image

www.ti.com

Basic Test Procedure

3.5

AFE7070 Performance Results

Figure 8

shows the typical two-tone performance of the AFE7070 EVM from the preceding setup.

Figure 8. Two-Tone IMD Performance: LO = 2.1 GHz, DAC Rate = 65 MSPS, IF = 4.5 MHz and 5.5 MHz

Note that some part-to-part variations can yield significantly improved two-tone IP3 performance. The
performance plots in this document show typical responses.

Revision History

Changes from Original (March 2012) to A Revision

.......................................................................................................

Page

Changed TSW3100 to TSW1400 in text and images throughout the entire document.

.........................................

1

Changed

Test Setup Block Diagram

image, replaced Ethernet with USB and changed the TSW3100 block to

TSW1400.

..................................................................................................................................

8

Changed entire

Test Setup Connections

section.

....................................................................................

8

Changed entire

TSW1400 Quick-Start Operation

section.

..........................................................................

9

Changed

TSW1400 Programming GUI

image.

.......................................................................................

9

Changed

TSW1400 Multitone Pattern

image.

.......................................................................................

10

Deleted first bullet in

AFE7070 Software Quick-Start Guide

section.

.............................................................

10

Changed all the values in the last bullet of the

AFE7070 Software Quick-Start Guide

section.

..............................

10

Added paragraph to the end of the

AFE7070 Software Quick-Start Guide

section.

............................................

10

Changed

Two-Tone IMD Performance:

image. Also changed IF values to 4.5 MHz and 5.5 MHz.

.........................

11

Deleted

WCDMA ACPR: LO = 2 GHz, DAC Rate = 57.6 MHz, 0-MHz Offset

image.

.........................................

11

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

11

SLOU337A – March 2012 – Revised July 2015

Revision History

Submit Documentation Feedback

Copyright © 2012–2015, Texas Instruments Incorporated

Содержание AFE7070


















Отзывы: