Texas Instruments ADS8861EVM-PDK Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 21

Texas Instruments ADS8861EVM-PDK Скачать руководство пользователя страница 12

PDK Kit Operation

7.2

Loading the ADS8861EVM-PDK Plug-in

Step 1.

Make sure the PDK kit is configured and powered up as explained in

. Then, press

the

Reset

button on the MMB0 (in the top right-hand corner) one time to clear board memory.

Step 2.

Connect the MMB0 to a computer using the USB cable provided with the kit.

Step 3.

Start ADCPro from the Windows

Start

menu.

Step 4.

Load the ADS886XEVM plug-in from the ADCPro drop-down

EVM

menu, as shown in

. Note that only one EVM plug-in can be loaded at a time. If a different plug-in is

selected, the previous plug-in is unloaded.

Figure 9. Loading EVM Plug-in

Step 5.

When the plug-in is loaded, the plug-in searches for the board. A series of messages in the
status area indicates this action, eventually showing

Connected to EVM

.

The plug-in is now loaded and ready to function with the ADS8861EVM.

12

ADS8861EVM-PDK

SBAU214 – October 2013

Submit Documentation Feedback

Copyright © 2013, Texas Instruments Incorporated

«
...
10
11
12
13
14
...
»

Содержание ADS8861EVM-PDK






















Отзывы:

Нет отзывов