Texas Instruments ADS8668 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 47

Texas Instruments ADS8668 Скачать руководство пользователя страница 10

Power Supplies

5

Power Supplies

The ADS86xxEVM can be powered from the simple capture card if onboard buffers for active low-pass
filters are not being used. The onboard regulator (U9) for generating high-voltage supplies (HVDD and
HVSS) is disabled by closing jumper J17. The HVDD and HVSS supplies are only required for buffers U4
and U5.

CAUTION

Do not open jumper J17 if the ADS86xxEVM must be powered only from the
simple capture card and an external 5-V supply is not provided on J32.

High-voltage supplies (HVDD and HVSS) for buffers U4 and U5 can be generated using the onboard
regulator (U9) if an external 5-V dc supply is provided on J32. The external 5-V dc supply must be at least
200 mV above the unregulated 5-V supply of the simple capture card. The external 5-V dc supply must be
capable of providing at least 500 mA of current.

provides jumper settings for generating HVDD

and HVSS using the onboard switching regulator U9.

Table 10. Jumper Settings for Generating HVDD and HVSS Using an Onboard Switching Regulator

Jumper

Position for Using an Onboard Switching Regulator

J12

Closed between pins 1 and 2

J14

Closed between pins 1 and 2

J17

Open

HVDD and HVSS for buffers U4 and U5 can also be generated by providing external high-voltage supplies
on J18, as shown in

and

illustrate the power-supply connections for external

supplies.

Table 11. Jumper Settings for Generating HVDD and HVSS from External High-Voltage Supplies

Jumper

Position for Generating HVDD and HVSS from External Voltage Supplies

J12

Closed between pins 2 and 3

J14

Closed between pins 2 and 3

J17

Closed

Table 12. Power-Supply Connections

Voltage

Voltage

Supply

Signal

Range

Pin Number

Note

Required only for generating HVDD and HVSS using the

External 5 V

EXT_5V

5 V to 5.5 V

J32.2

onboard switching regulator

—

GND

GND

J32.1

—

Required only for generating HVDD and HVSS from external

External HVDD

EXT_HVDD

16 V to 25 V

J18.3

high-voltage supplies. Make sure HVDD + |HVSS| < 36 V.

Required only for generating HVDD and HVSS from external

External HVSS

EXT_HVSS

–16 V to –25 V

J18.1

high-voltage supplies. Make sure HVDD + |HVSS| < 36 V.

—

GND

GND

J18.2

—

10

ADS86xxEVM-PDK Evaluation Module

SBAU245A – June 2015 – Revised July 2015

Submit Documentation Feedback

Copyright © 2015, Texas Instruments Incorporated

«
...
8
9
10
11
12
...
»

Содержание ADS8668
















































Отзывы:

Нет отзывов