Texas Instruments ADS54J64 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

background image

Quick Start Guide

7

SBAU290 – September 2017

Submit Documentation Feedback

Copyright © 2017, Texas Instruments Incorporated

ADS54J64 Evaluation Module

2.3.2

HSDC Pro GUI Configuration

Set up the HSDC Pro GUI by following these instructions.

1. Open High Speed Data Converter Pro from the Start Menu

→

All Programs

→

Texas Instruments

→

High Speed Data Converter Pro.

shows the GUI main page.

Figure 3. HSDC Pro GUI Main Panel

Figure 4. HSDC Pro Sampling Rate and Additional Device Parameters

2. When prompted to select the capture board, select the TSW14J56, whose serial number corresponds

to the serial number on the TSW14J56EVM, and click OK.

3. Select the ADC tab at the top of the GUI.

4. Use the Select ADC drop-down menu in the top-left corner to select

ADS54J64_LMF_4841_mode01

.

5. When prompted to update the firmware for the ADC, click the Yes button, and wait for the firmware to

download to the TSW14J56.

«
...
5
6
7
8
9
...
»

Содержание ADS54J64

























Отзывы:

Нет отзывов

Похожие инструкции для ADS54J64

Бренд: ABB Страницы: 2

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

Бренд: Dantherm Страницы: 96

C-NaviGator III

Бренд: C-Nav Страницы: 20

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: IDS Страницы: 2

Бренд: RAKwireless Страницы: 6

Бренд: GEA Страницы: 47

XP-9 88-IoT Series

Бренд: ICP DAS USA Страницы: 8

Бренд: ICON Страницы: 2

Бренд: ICP DAS USA Страницы: 4

Бренд: Greenheck Страницы: 4

Бренд: Dickey-John Страницы: 109

by-me Eikon 20526

Бренд: Vimar Страницы: 6

SYNCHRO QUASAR AC

Бренд: UCS Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды