Texas Instruments ADS131E08EVM-PDK Скачать руководство пользователя страница 4

Страница: 4 / 39

ADS131E08EVM Overview

www.ti.com

SBAU200C – June 2012 – Revised April 2020

Submit Documentation Feedback

Performance Demonstration Kit for the ADS131E08

1.4

ADS131E08EVM Hardware

Figure 2

shows the hardware included in the ADS131E08EVM kit. Contact the factory at

http://e2e.ti.com

if any component is missing. Also, it is highly recommended that you check the TI website at

http://www.ti.com

to verify that you have the latest software.

Figure 2. ADS131E08EVM-PDK Kit

The complete kit includes the following items:

•

ADS131E08EVM printed-circuit board (PCB)

•

MMB0 (modular EVM motherboard)

An external power supply is required to power the MMB0 board. Any supply used to power the MMB0
board through the jack located at J2 must comply with the following requirements:

•

Output voltage: 5.5 VDC to 15 VDC

•

Maximum output current:

≥

500 mA

•

Output connector: barrel plug (positive center), 2.5-mm I.D. x 5.5-mm O.D. (9-mm insertion depth)

•

Complies with applicable regional safety standards

Содержание ADS131E08EVM-PDK








































Результаты поиска

Содержание ADS131E08EVM-PDK

Отзывы:

Texas Instruments ADS131E08EVM-PDK, Руководство пользователя, Страница: 4 / 39

Результаты поиска

Содержание ADS131E08EVM-PDK

Отзывы: