Texas Instruments ADS131E08EVM-PDK Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 39

Texas Instruments ADS131E08EVM-PDK Скачать руководство пользователя страница 11

ADS131E08EVM Daughter-Card Hardware Overview

11

SBAU200C – June 2012 – Revised April 2020

Submit Documentation Feedback

Copyright © 2012–2020, Texas Instruments Incorporated

Performance Demonstration Kit for the ADS131E08

The front-end board must be properly configured in order to achieve the various power-supply schemes.
The default power-supply setting for the ADS131E08EVM is a bipolar analog supply of ±2.5 V, and there
are onboard options to switch to a unipolar analog supply of +3 V. The digital supply (DVDD) is selectable
to 3.3 V or +1.8 V.

shows the board and component configurations for each analog power-

supply scheme.

shows the board configurations for the digital supply. Note that the EVM is

shipped with the analog supply set to ±2.5 V and digital supplies set to 3.3 V.

Table 3. Analog Supply Configurations

AVDD and AVSS

Unipolar Analog Supply

Bipolar Analog Supply

3 V

5 V

±1.5 V

±2.5 V

JP7

1-2

1-2

2-3

2-3

JP1

2-3

2-3

1-2

1-2

U6

TPS73230

TPS73250

Don't care

Don't care

U8

Don't care

Don't care

TPS73201

TPS73201

U7

Don't care

Don't care

TPS72301

TPS72301

R61

Don't care

Don't care

21 k

Ω

47.5 k

Ω

R62

Don't care

Don't care

78.7 k

Ω

43.2 k

Ω

R59

Don't care

Don't care

23.3 k

Ω

49.9 k

Ω

R60

Don't care

Don't care

95.3 k

Ω

46.4 k

Ω

C48, C54, C59

Not installed

Not installed

Not installed

Not installed

Table 4. Digital Supply Configurations (DVDD and

DGND)

DVDD

3.3 V

1.8 V

JP11

2-3

1-2

«
...
9
10
11
12
13
...
»

Содержание ADS131E08EVM-PDK








































Отзывы:

Нет отзывов