Texas Instruments ADC3541EVM Скачать руководство пользователя страница 4

Страница: 4 / 14

3 Setup Procedure

3.1 Install High-Speed Data Converter (HSDC) Pro Software

Download the most recent version of the

HSDC Pro

software. Follow the installation instructions to install the

software.

Download and install the

HSDC Pro Patch

. This patch copies all the INI files required to the HSDC pro directory.

3.2 Install the Configuration GUI Software

Download the Configuration GUI software from the EVM tool folder at

ADC3541EVM

Extract and run the executable file, and follow the instructions.

3.3 Connect the ADC EVM and TSW1400EVM

Connect the

ADC3541EVM

FMC connector to J1 of the FPGA Interposer Card.

Connect J2 of the FPGA Interposer Card to J1 of the TSW1400EVM.

Figure 3-1. ADC3541EVM Full Setup

3.4 Connect the Power Supply and Mini-USB Connections

Use the following steps to connect the power supply and mini-USB connections:

1. Connect 3.3 VDC to TP2 of the FPGA Interposer card. Provide power supply ground to TP1, as required. J10

of the TSW1400EVM can be used to source this +3.3 VDC.

2. Connect the power cable to the TSW1400EVM at 5-V (minimum 3 A) power supply. Place the power switch

(SW7) to the "On" position.

Setup Procedure

www.ti.com

ADC3541EVM Evaluation Module

SBAU294 – JULY 2020

Submit Document Feedback

Содержание ADC3541EVM















Результаты поиска

Содержание ADC3541EVM

Отзывы:

Похожие инструкции для ADC3541EVM

Бренды по названию

Популярные бренды

Texas Instruments ADC3541EVM, Руководство пользователя

Результаты поиска

Содержание ADC3541EVM

Отзывы:

Похожие инструкции для ADC3541EVM

Бренды по названию

Популярные бренды