Texas Equipment FX 815TG, Руководство пользователя

Страница: 18 / 28

18
Troubleshooting
The motor will not start
1. Check the fuel control is set correctly.
2. Check the spark plug.
3. Check there is fresh gas in the tank.
4. See separate motor instructions for further
troubleshooting.
The motor is not running smoothly
1. Ensure the throttle control is not set to max.
2. Check there is fresh gas in the tank.
The blades will not rotate
1. Check for stones lodged between the blades.
2. Release any stones by removing the blades.
3. Check the cables are in good working order and fitted
correctly.
4. Check the belt is in good working order and fitted
correctly.
5. Ensure the belt tensioner is adjusted correctly.
The blades will not stop
1. Stop the engine and contact your dealer.
Noise, vibration and precautionary measures
1. Long-term exposure to noise levels exceeding 85 dB (A)
are damaging. Always use ear defenders when the
machine is being used.
2. Reduce the running speed of the motor to reduce
vibration and noise levels.
3. To reduce noise levels further, only use the machine in
an open environment.
4. Vibrations can be reduced further by holding the handle
firmly.
5. To avoid disturbing others, the machine should only be
used during the daytime.
6. Always wear close-fitting work clothes, hard-wearing
work gloves, ear defenders and non-slip boots with steel
toecaps.
7. Take a 30-minute break every 2 working hours.
8. A worn belt must be replaced/ serviced by an authorized
dealer
Technical specifications
Model FX 815TG
Engine 212 cc TG725
Engine rotations/min 3600 rpm (no-load)
Blade rotations/min 82-113 rpm (no-load)*
Working width 36-62-85 cm
Working depth 30 cm
Gear 2+1 (R-1-2)
Weight 76 kg
Vibration level left / right handle
Uncertainty 8.1 / 7.4 m/s 2
1.5 m/s 2
Sound pressure level L
pA
Measure uncertainty
86.1 dB(A)
3 dB
Sound power level L
wA
Measure uncertainty
98 dB(A)
3 dB
* Measured at the center of blade shaft.
Warranty terms and conditions
The warranty period is 2 years for private end users in EU
countries.
Products sold for commercial use, only have a warranty
period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are NOT
covered by the warranty.
Wearing parts, which are NOT covered for more than 12
months:
•
Blades
•
Cables
•
Belts
•
Switches
•
Membranes/gaskets
•
Spark plugs
•
Engine liquids (oil, gasoline)
•
Starter cords
•
Filters
If you start the engine without adding oil, it will be damaged
and cannot be repaired and therefore not covered by the
warranty.
The warranty does NOT cover damages/faults caused
by:
•
Lack of service and maintenance
•
Structural changes
•
Exposure to unusual external conditions
•
Damages to the bodywork, deck, handles, panels etc.
•
If the machine has been improperly used or overloaded
•
Wrong use of oil, gasoline or other liquid types, which
are not recommended in this user manual
•
Bad or dirty gasoline, which results in contamination of
the fuel system
•
Use of unoriginal spare parts.
•
Other conditions where Texas cannot be held
responsible.
Whether a case is a warranty claim or not is determined in
each case by an authorized service center.
Your receipt is your warranty note, why it should always be
kept safe.
REMEMBER: The purchase of spare parts as well as any
request for warranty repair, art. no. (e.g. 900631XX), year
and serial number should always be informed. It can be
found on the name-plate on the machine!
* We reserve the right to change the conditions and accept
no liability for any misprints