Texas Andreas Petersen Smart 3700, Руководство пользователя

Страница: 11 / 12

11
Illustration 8+9+10:
Connect the extension cord to the appliance inlet on the
switch box. About 30 cm from the end, creade a loop in
the cable. Guide the loop through the oval hole of the
cable strain relief, and over the hook. Carefully pull it
tight.
Operating
Illustration 11-12:
1. Press the safety switch (1) and pull the activation
handle (2).
2. Hold the handle (2) when using the mower. Release
the handle (2) and the mower stops.
Be aware that the blades rotate for another 5
seconds after the handle is released.
Adjustment of cutting height
Illustration 13:
The cutting height is adjusted by the handle at the side
of the machine.
Cutting method
Illustration 14:
It will be useful to start working from at a point close to
the power supply and to work your way away from the
supply. Cut the lawn at a suitable angle from the power
supply and place the power cable to the side, which has
already been cut.
For mulching insert the mulching plug as shown in
Illustration 2 (12)
Maintenance
Always make sure the the lawn mower is cleaned and
no grass stuck to is. Remove the grass with a bruch
every time the mower has been used. Do not use water
for this purpose.
Change the knife by loosening the bolt, replace the knife
with a new and replace the bolt.
Always check that the knife is properly fastened and in
balance after replacement.
Risk of overheating
Should the motor stop during use, it can be caused
by overheating. This product is equipped with a
thermos switch, which will stop the motor if it is being
used too hard. If that happens, let the motor cool off
for 5 minutes before starting it again.
If the machine cuts in long and wet grass or if it
continues to operate, while the collection box is full,
there is a high risk of overheating.
If the machine overheats, its thermal cutout will trip and
cause the machine to stop.
The machine will be able to be used again once it has
cooled down sufficiently. Cooling takes up to 5 minutes.
If you frequently experience this problem, it is
recommended to increase the cutting height, push it at a
slower speed and make sure the collection box is not
full. If the grass is long and wet, the rear discharge hole
can easily be blocked even if the collection box is not
full. Therefore, check and clean often.
Specifications
Model Smart 3700 Smart 4400
Voltage 230-240V 230-240V
Effect 1600 Watt 1800 Watt
Cutting width 37 cm 44 cm
Collector box 45 L. 55 L.
Height adjustment 25-75 mm 20-75 mm
Weight 13 kg 16,5 kg
Warranty terms and conditions
The warranty period is 2 years for private end users in
EU countries.
Products sold for commercial use, only have a warranty
period of 1 year.
The warranty covers material and/or fabrication faults.
Restrictions and requirements
Normal wear and replacement of wearing parts are NOT
covered by the warranty.
Wearing parts, which are NOT covered for more than 12
months:
•
Blades
•
Cables
•
Belts
•
Fuses
•
Switches
If you start the engine without adding oil, it will be
damaged and cannot be repaired and therefore not
covered by the warranty.
The warranty does NOT cover damages/faults
caused by:
•
Lack of service and maintenance
•
Structural changes
•
Exposure to unusual external conditions
•
Damages to the bodywork, deck, handles, panels
etc.
•
If the machine has been improperly used or
overloaded
•
Use of unoriginal spare parts.
•
Other conditions where Texas cannot be held
responsible.
Whether a case is a warranty claim or not is determined
in each case by an authorized service center.
Your receipt is your warranty note, why it should always
be kept safe.
REMEMBER: The purchase of spare parts as well as
any request for warranty repair, art. number (e.g.
90063XXX), year and serial number should always be
informed. It can be found on the CE-label placed on the
deck.