manualshive.com logo in svg

Tesup i-1500, Руководство пользователя


Поделиться
Скачать
background image

Preparing to use the system

Feed the three-wire cable through the tower right up to the top.

Provide suitable strain relief.

Connect the wires to the generator.

Fig. 8:

Connecting the three-wire cable to the generato

Pull heat shrink tubing over the solder joint and shrink.

Wrap each wire with textile insulating tape.

Danger due to unsuitable tower constructions!

Only  use  tested  mast  constructions  or original  

TESUP

 masts .

7

.6

Erecting the wind turbine

WARNING!

        

 

Pull a suitable shrink tube over each wire of the cable.                                                                 

                     

  

Twist and solder each wire of the cable to the wire from the generator

Short circuit all 3 phases to activate the generator brake

.

1

                                                     

1

When using the 

TESUP

 charge controller, press the brake button

Choose a mast diameter <70 mm, so that the rotor blades are 

not pressed against the mast during a storm.

Attach the wind turbine to the tower. Be careful not to damage the cable.

Screw wind generator to mast.

Erect the mast.

Align the mast vertically in all directions.

Brace the vertical mast (see Fig. 5)

Kurzschluss aufheben.

14

Содержание i-1500


























Отзывы:

Нет отзывов

Похожие инструкции для i-1500

Бренды по названию

Популярные бренды

Загрузить еще бренды