manualshive.com logo in svg

TestPad BTS-2002H, Руководство пользователя

Поделиться
Скачать
TestPad BTS-2002H Скачать руководство пользователя страница 23

Shenzhen TestPad Electronic Co., Ltd.

http://www.test-pad.com

23

Battery Charge

After selecting this mode, you can charge batteries separately. For information about the setting

method and display mode, refer to Capacity Test. After you press ENTER, the tester charges the

selected battery. When the charge is completed, the whole process ends.

Battery Discharge

After selecting this mode, you can discharge batteries separately. For information about the setting

method and display mode, refer to Capacity Test. After you press ENTER, the tester discharges the

selected battery. When the discharge is completed, the whole process ends.

Program DC Power

Select this mode, and then press ENTER to DC power supply mode, as shown below.

Constant voltage mode

The tester is On.

Setting voltage.....

Output voltage

Setting current.....

Output current

By default, the power supply is disabled. Press ENTER to enable the power output, or press enter

again to disable it.

1.

CV: The battery is working in constant-voltage mode; CC: The battery is working in

constant-current mode.

2.

ON: The tester is switched on; Off: The tester is switched off.

3.

Vs=1.00V: The voltage is set to 1.00V.

4.

Is=1.00A: The maximum output current is set to 1A.

5.

Vo=1.00V: The current output voltage is 1.00V.

DC Power Supply

CV

ON

->Vs= 1.00V

Vo= 1.00V

Is= 1.00A

Io= 0.090A

Содержание BTS-2002H




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды