background image

 

19

 

 

   

2.3.2 Timing Table Chart   

 

Mode 

NO 

Resolution 

H-Freq. (KHz) 

Band Width 

(MHz) 

Polarity 

102 

720x400 70Hz 

31.47 

28.322 

 

 

103 

VGA 640x480 60Hz 

31.47 

25.175 

 

 

182 

MAC 640x480 66Hz 

35 

30.24 

 

 

173 

640x480 72Hz 

37.86 

31.5 

 

 

109 

640X480 75Hz 

37.5 

31.5 

 

 

104 

800x600 56Hz 

35.16 

36 

 

 

116 

800x600 60Hz 

37.88 

40 

 

 

110 

800x600 72Hz 

48.077 

50 

 

 

117 

800x600 75Hz 

46.875 

49.5 

 

 

10 

108 

832x624 (74.55Hz) 

49.722 

57.28 

 

 

11 

118 

1024x768 (60.0 Hz) 

48.363 

65 

 

 

12 

157 

1024x768 (70.0 Hz) 

56.476 

75 

 

 

13 

141 

1024x768 (75.0 Hz) 

60.02 

78.75 

 

 

 

Note: If input H-display > 1024 pixel or V-display > 768 lines or V-Sync >76Hz, then 
OSD shall display warning out of range. 

 
 

2.3.3 EDID Data 

 

DP/HDMI 

The monitor assembly shall provide a display communications channel that 
conforms to VESA DDC2B hardware requirements. This configuration shall contain 
the 256-byte EDID file as specified by VESA EDID Standard. 

 

VGA 

The monitor assembly shall provide a display communications channel that 

conforms to VESA DDC2B hardware requirements. This configuration shall contain 
the 128-byte EDID file as specified by VESA EDID Standar 

Содержание APM-15

























Отзывы: